430 mm 430 mm 32 mm C LA 600 mm d%3D0.75m 300 mm 150 mm D (b) Top view 64 mm X 64 mm X 3 mm B y 600 mm D 430 mm 900 mm (a) PROB. 30 31. Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure. The rack is made up of 50 mm X 50 mm steel tubing which is 3 mm thick. Assume that the weight of each of four bicycles is distributed evenly between the two support arms so that the rack can be represented as a cantilero beam (ABCDEF) in the x-y plane. The overall weight of the rack alone is W 270 N directed through C, and tie weight of each bicycle is B = 135 N.

430 mm 430 mm 32 mm C LA 600 mm d%3D0.75m 300 mm 150 mm D (b) Top view 64 mm X 64 mm X 3 mm B y 600 mm D 430 mm 900 mm (a) PROB. 30 31. Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure. The rack is made up of 50 mm X 50 mm steel tubing which is 3 mm thick. Assume that the weight of each of four bicycles is distributed evenly between the two support arms so that the rack can be represented as a cantilero beam (ABCDEF) in the x-y plane. The overall weight of the rack alone is W 270 N directed through C, and tie weight of each bicycle is B = 135 N.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The horizontal shaft AD is attached to a fixed base at D and is subjected to the torques shown. A 44-mm-diameter hole has been drilled into portion CD of the shaft. The entire shaft is made of steel for which G = 77 GPa. 1. Calculate the torque in segment CD in N.m. 2. Calculate the torsional shear stress on the surface of segment BC in MPa. 3. Calculate the angle of twist of segment AB in degrees. 4. Calculate the angle of twist of point A relative to point D in degrees.
Calculate the normal stress due to flexure at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.
1) a Compressor with a diameter of 0,65 metres and a thickness (t)= 4mm Sigmax= 42 MPA and Sigmay=84MPA Calculate: The pressure P and Maximum In-Plane Shear Stress Tmaxvlak in MPA 2) an element has undergoing a rotation of Theta= 30 degrees Sigmax= 75 MPA and sigma y= 55 MPA. Calculate X', Y' and Txy" in MPA 3) A uniform Beam with a lenght of 2 metres to a-a and forces N=12kn and V=4kn. Calculate the main stresses sigma1 and sigma 2 [in MPA] 4) an element with the given stresses: Sigmax=75 MPA and Sigmay= 55 MPA Calculate the Absolute maximum shear stress in MPA )Tabsmax)
Draw the shear force and bending moment diagram of the beam. Draw the distribution of normal stress and shear stress in the cross section of the beam at the B support. q=12t/m b=85mm h= 750mm t=30mm
Determine the following unknowns on the beam shown below using Area-Moment Method. Consider 150 mm x150 mm section and E = 80 GPa. Show complete and organized solution. a. Vertical Reaction at B in kN. b.Moment Reaction at A in kN-m. c. Deflection at point C in mm. d. Deflection at midspan of AB in mm. Given: a- 7m b- 24kN/m C- 30kN
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
The solid steel shaft carries the torques T1= 1200 Nm and T2=750 N m. Using L1=L2=2.5 m and G = 83 GPa, determine: a. draw a diagram using a double headed arrows showing the torque in each segment b. determine the shear stresses in each segment and the angle of rotation of the free end if the diameter is 100 mm. c. the smallest allowable diameter of the shaft if the shear stress is limited to 60 MPa and the angle of rotation of the free end is not to exceed 4^0.
1-10. A bar of variable cross section, held on the left, is subjected to three forces, P =4 kN, P, = -2 KN, and P, = 3 kN, as shown in the figure. On two separate diagrams, plot the axial force and the axial stress along the length of the bar. Let A1, = 200 mm, A2, = 100mm², and A3, = 150 mm".
l = 20'0" w = 2 kips / ft Beam: W21 x 50 FIND: - Maximum Shear - Maximum Moment - Maximum Deflection -The stress due to bending and shear stress in the web.
Given the following data:Cross section: 50mm x 75mmP = 200 kNθ = 15 ° with the x-axis Find the shear stress (in MPa) on plane A-A.
What is the reaction at A?a. 45 KN c. 60 KNb. 15 KN d. 75 KN What is the maximum shearing stress?a. 45 KN c. 30 KNb. 15 KN d. 90 KN What is the maximum moment?a. 60 KN.m c. 45 KN.mb. 120 KN.m d. 90 KN.m What is the centroid with respect to x-axis?a. 214.29 mm c. 180.50 mmb. 350.25 mm d. 432.75 mm What is the moment of inertia with respect to the neutralaxis?a. 2,733.73 x 106 ??4 c. 2,598.11 x 106 ??4b. 2,222.22 x 106 ??4 d. 2,639.73 x 106 ??4 What is the value of the maximum bending stress?a. 8.125 MPa c. 10.715 MPab. 5.375 MPa d. 12.325 MPa
Calculate the shear stress at the flange level to web Interface at A. Ixx= 1,241 in^4. Bending moment (M)= 350 ft-kips. Shear (v)= 80 kips.