452 Surface Production Operations Problem 2. Given the following data, determine the height of the external leg for a gunbarrel. Oil gravity Water gravity Oil outlet height Interface height Water outlet height= 45 cm, = 45°API, = 1.05, = 9.15 m, = 5.5 m,

452 Surface Production Operations Problem 2. Given the following data, determine the height of the external leg for a gunbarrel. Oil gravity Water gravity Oil outlet height Interface height Water outlet height= 45 cm, = 45°API, = 1.05, = 9.15 m, = 5.5 m,

Name: 452Surface Production OperationsProblem 2.Given the following data, d
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 452Surface Production OperationsProblem 2.Given the following data, determine the height of the external leg for agunbarrel.Oil gravityWater gravityOil outlet height|Interface heightWater outlet height= 45 cm,= 45°API,= 1.05,= 9.15 m,= 5.5 m,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.A vertical cylindrical tank has an orifice for its outlet. When the water surface in the tank is 5 m above the orifice, the surface can be lowered 4 m in 20 minutes, the pressure on the surface being atmospheric. What uniform air pressure must be applied to the surface if the same volume of water is to be discharged in 10 minutes?
Given the sketch shown below, the diameter of the plunger Dp = 8 cm. The Ram diameter is Dr = 48 cm. The efficiency is 100%, the stroke of the plunger is 18 cm. The ram has to raise a load F2 = 2kN. Find: A) the force f1 exerted on the plunger. B) the number of strokes needed to raise the load given above by a distance of 10 cm. C) the volume of oil pumped if the load moves by 20 cm ( using plunger force in a ) D) what will be the new diameter of the ram piston if the new load force is 16 times the force exerted in the plunger the diameter of the plunger is kept to 8 cm.
Rover weight capacity 35 kilo grams (payload)Rover measurements:Wheel distance - 14.5 inches and 8.5 inchesRover platform size (width & length) 14.4 inches x 10.4 inchesHeight- 15.8 inches Water tank selectionMore or less 25 liters*For tank selection we need to justify the size with the center of gravity, proving that is themaximum dimension or liters of the tank because the center of gravity will be higher makingthe rover prone to topplingPump selection*Our sprayer design has two nozzles which splits using a tee splitter, we need to find thesize of the pump to obtain the same discharge rate of a normal sprayer. A normal sprayerhas a 12V pump and a pressure from 0.2 to 0.45 mpa (30-65 psi)The application rate of the main pesticide is 9.6 - 19.2 fl oz/A (Brigade Insecticide for sweetpotato)Thai was the initial deign where the water tank is above the battery and pump, but wechanged our mind, now it is the battery and pump above the waterBattery selection* once the size of the pump…
A pump delivering 5000 g.p.m. of 60° F. water has a 16-in.-diameter suc- tion pipe and a 14-in. discharge pipe. The suction vacuum gage, which is 3 in.) below the pump centerline, reads 5 in. of mercury (below atmospheric pressure). The discharge gage, which is 18 in. above the pump centerline, reads 10.6 lb. per sq. in. ga. What is the head of the pump? The specific gravity of mercury is 13.6.
Hello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1.Question : An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal placesAnswer: 2.554
After graduation, you work for a pump manufacturing company. One of your company’s best-selling products is a water pump, which we shall call pump A. Its impeller diameter is DA = 6.0 cm, and its performance data when operating at n. A = 1725 rpm (?A = 180.6 rad/s) are shown in Table.The marketing research department is recommending that the company design a new product, namely, a larger pump (which we shall call pump B) that will be used to pump liquid refrigerant R-134a at room temperature. The pump is to be designed such that its best efficiency point occurs as close as possible to a volume flow rate of V. B = 2400 cm3 /s and at a net head of HB = 450 cm (of R-134a). The chief engineer (your boss) tells you to perform some preliminary analyses using pump scaling laws to determine if a geometrically scaled-up pump could be designed and built to meet the given requirements. (a) Plot the performance curves of pump A in both dimensional and dimensionless form, and identify the best…
A ship with vertical sides near the water line, weighs 40 MN and draws 6.7 m in salt water (specific gravity = 1.026). Discharge of 2 MN of water ballast decreases the draft to 6.4 m. What would be the draft d of the ship in fresh water?
Explain with the aid of diagram the action of the hydraulic press The following data pertains to a hydraulic press: The diameters of the plunger and ram are 50 mm and 0.5 m respectively. The ram is 1.75 m below the plunger and the mass density of the liquid in the hydraulic press is 820 kg/m³. The mass of the plunger and the ram are 6 kg and 400 kg respectively. The plunger is forced vertically down by a lever with a mechanical advantage of 6 to 1 onto which a force of 800 N is applied. The ram moves upwards when the plunger moves downwards. Determine the maximum lifting force exerted by the ram.
PROCESS INSTRUMENTATION AND CONTROL In a close tank, the close tank specifications are as follows: X=100 inches, Y=10 inches, d=120 inches ,specific gravity of tank liquid is 0.8 and specific gravity of seal liquid is 0.9. Find (i) Span (ii) Equivalent head of water at maximum level. (iii) Equivalent head of water at minimum level
A pump delivers 20 cfm of water having a density of 62 lbs. per cubic foot. The suction anddischarge gage reads 5 inches Hg vacuum and 30 psi respectively. The discharge gage is 5 ft abovethe suction gage. If pump efficiency is 70%, what is the motor power?
Express movement energy of mechanical energy, pressure, kinetic energy losses and power of pump by using fundamentals of unit analysis in terms of water column height the height of the water column refers to the static pressure exerted by the water.
A2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:3. Determine the volumetric flow rate, in L/s, for water flowing out of a faucet based on 6 L in 8 s.