5. Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor and the load current of 215 A.If it is desired to improve the power factor determine the following. (a) The uncorrected power factor and reactive load. (b) The new corrected p.f after installing a shunt capacitor unit with a rating of 350kvar.

5. Assume that a 2.5-kV 1-phase circuit feeds a load of 450 kW at a lagging load power factor and the load current of 215 A.If it is desired to improve the power factor determine the following. (a) The uncorrected power factor and reactive load. (b) The new corrected p.f after installing a shunt capacitor unit with a rating of 350kvar.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.41P

See similar textbooks

Similar questions

A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
In the above figure, a single line model of a three-phase power system is given. Base power 50MVA, base voltage 13.8kV according to its value, a) Per-unit values of power system circuit elements according to the given base power and base voltage values. calculate. b) The perunit you calculate by drawing the equivalent impedance circuit for one phase of the power system given in the figure. show on the values.
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
Q1: Perform load line analysis for the following circuit using the figure given below. Where E=20V.R=5Kohm
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.
Enlist the power quality issues for renewable energy integration
1. Write down a formula for the three-phase active power, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula for the three-phase reactive power, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements 3. Write down a formula for the three-phase apparent power, assuming perfectly sinusoidal and symmetrical conditions, using line-neutral voltage measurements.
Obtain the power side current, transmission line current, load current, load stage voltage and load power using the unit method for the three phase system below (the generator line-to-line voltage is 13.2 kV and the base value of the three phase power is 50 MVA).
Draw an impedance diagram for the electric power system shown in the figure attached, showing all impedances in per unit on a 100-MVA base. Choose 20kV as the voltage base for generator. The three-phase power and line-line ratings are given in the figure attached.
Power Transmission and Distribution Discuss the advantages and disadvantages of single-phase and three-phase system
A three-phase symmetrical double circuit line is arranged in a horizontal plane as shown in figure below. Calculate and derive an expression for the transposed line for the inductance. Assume balanced equally distributed loads