50 mm M 15 mm B 150 mm

Q: The rigid beam is supported by a pin at A and aluminum wires BD and CE. If the beam displaced 3.4 mm…

A: Given data          If the beam displaced by…

Q: Strength of materials 2020/2021 + Draw the free-body diagram (FBD) for the beam shown and determine…

A: given data; ⇒L=1.5m⇒force(F)=12KN⇒load intensity (w)=10KN/m⇒moment (M)=5KN-m

Q: A beam carries a uniform distributed load of intensity w in N/m. It was determined that Vmax = 3.75w…

A: Note:- As per our company guidelines we are supposed to answer only the first three sub-parts.…

Q: The shape of the beam made of U profile ensures safe loading. Find the length c of the overhangs so…

A:

Q: The beam shown below has a cross section of channel shape with width b=D400 mm and height h=80 mm,…

A: Answer: The maximum tensile and compressive stresses in the beam are 64.68 MPa and 16.36 MPa…

Q: The piston of an automobile engine is held to the connecting rod by a wrist pin having an external…

A: (a) To find: The bearing pressure between rod end and the wrist pin. Given: The outer diameter of…

Q: Problem 1: Slab design using the ACI moment coefficients Design the continuous slab shown using the…

A: The continues slab weight of concrete 24kn/m3 service load 14kn/m fy=420 mpa f'c=28mpa BY using ACI…

Q: A wooden cantilever 2 m long having a rectangu- lar cross-section 120 × 200 mm² is loaded by a…

A: We know that a 2 m long wooden cantilever with a rectangular cross section of 120 mm is loaded at…

Q: A 1 m length of the bar shown in Fig. 9.17 is used as a cantilever beam. A concentrated load P = 2.5…

A: We know that a cantilever beam is made up of a 1 m length of the bar illustrated in the diagram.At…

Q: 334. A beam simply supported at the ends has the cross section and is leaded with a concentrated…

A: When a beam is loaded it tends to bend and a bending moment acts upon it. As a result, longitudinal…

Q: A wooden log is to be used as a footbridge to span 3.50-m gap. The log is required to support a…

A:

Q: PROBLEM 2-30 The W250x22 cantilevered beam is made of A-36 steel and it is subjected to the loading…

A:

Q: 8.28 The rectangular beam ABC, 100 mm wide by 400 mm deep, is supported by a pin at A and the cable…

A:

Q: 1 A 250 mm x 125 mm I-beam having I, 3717-8 W V, y 30° U, x cm² and Iy = 193-4 cm4 is used as a…

A: A 250 mm×125 mm I-beam with Ix=3717.8 cm4 and Iy=193,3 cm4 is utilised as a purlin on a roof truss…

Q: BP1: A simply supported rectangular beam with length= 5', height =5", and depth = 1" is loaded with…

A: According to the given information, we assume that 1 material is homogeneous and isotropic  2 Is…

Q: SITUATION: Given a 4 m cantilever beam carries a concentrated load Pat the free end. If the beam is…

A: given; length of cantilever beam(L)=4mload acting free end=Pfor…

Q: Determine the minimum height h of the beam shown in Figure below, if the flexu ral stress is not to…

A:

Q: A composite simply supported beam of span 10m and carrying a point load of 800N at its mid- span, is…

A:

Q: Q2 A beam is of T section, as shown in fig. The beam is simply supported over a span of 4m and…

A: w=42.7 kNmAnd in case of simply supported beam with UDL , maximum bending moment is given…

Q: A strip of steel 3 mm thick and 35 mm wide is bent round a cylindrical drum 4 mm in diameter.…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: Given: The rigid beam is supported at its ends by two A-36 steel tie rods. (Figure 1) The rods have…

A:

Q: P9-5. The rigid beam supports the load of 60 kN Determine the displacement at 8. Take E = 60 GPa,…

A: Let's draw free body diagram of 'AB' and 'BC' Assuming 'A' and 'B' simple supports…

Q: A beam which is composed of concrete and a wide flange steel is subjected to moment M = 1146 kN.m. W…

A:

Q: The allowable shear stress is Tallow = 805 psi. The supports at A and B are smooth. B 3 ft 6 ft -3…

A: Find the maximum allowable distributed load Given data  Maximum shear stress = 805 psi

Q: A beam 10 m long is simply supported 1 m from each end. It is made of two C 380 x 50 channels…

A: From the property tables of channels, we can get the properties of channel C380 x 50 as follows:…

Q: The bar is connected to the support using a pin having a diameter of d =lin. If the allowable…

A:

Q: Determine the maximum stress in a hollow column of Do = 160mm and Di = 100mm that supports a load of…

A: M=4kNm Do=160mm Di=100mm

Q: A simply supported beam is subjected to alinearly varying distributed load q(x) =(x/L)q0 withmaximum…

A: AY=Reaction force at ABy=Reaction force at Bq(x)=x4q0

Q: A circular cylindrical shaft is made of steel with yield stress ys = 700 MPa. The shaft is…

A:

Q: A composite section will be used to support a heavy axial load of P = 800 kN with a rigid plate at…

A:

Q: Determine the minimum height h of the beam shown in Fig. P-508 if the flexural stress is not to…

A:

Q: A steal structure is loaded as shown. Knowing that F-10 kN and L-1 m: di design the rod CD, if a-100…

A:

Q: Q 2: A cantilever beam has the profile shown so that it will provid sufficient clearances for large…

A: Given

Q: Find the maximum shear force (V), the cross section can carry if the maximum shear stress is not to…

A:

Q: lo09/A timber beam 15ommWide by 2 Bomm. deep is to be veinforced at the top and bottem by steel…

A:

Q: Consider the beam and loading shown. The allowable normal stress for the steel used is 152 MPa.…

A: Given Data The allowable normal stress acting on the steel is: σ=152 MPa The load acting on the…

Q: A girder ABCDE bears on a wall for a length BC and is prevented from overturning by a holding-down…

A:

Q: Frame Stonckure 1 Giveni .P= 9o kips . AD is of 5 En (0in rigid beam, with dimensions + 2 in x 4 in…

A:

Q: runs through the beam so that no tensile stress is developed in the concrete at its center section…

A: Given: TO determine: Tensile stress developed in the concrete beam when normal stress is 0

Q: Q3 The inclined beam is suffered by king eat (1) vollar alf) Detrimine the load at (1) and () and B…

A:

Q: Investigate if the W250 * 58 beam can safely support the loading. The beam has an allowable normal…

A: Draw the free-body diagram of the beam by taking the overhang section as a cantilever beam as shown…

Q: Q20/ The value of the normal stress due to flexural force 10 kN applied on the beam at * :the…

A: The value of the normal stress due to flexure force of 10 kN applied on the beam at the neutral axis…

Q: Determine the minimum height exceed 20 MPa. I= bh²³ € 12 my J 2.5 kN/m Rislo m 8.5 1m of the beam…

A: Given: σmax=20Mpa b = 80mm

Q: A Simpe beam is loaded. If the load P-120 KN determine the maximum tensile and compressive Stresses…

A:

Q: . A beam sinmply supported at the concentrated load P as shown in Fig. P-1334. If the maxımun…

A: given data;maximum flexural stress (τ)=20ksi=20*103lb/in2

Q: If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress…

A:

Q: Determine the minimum required failure shear stress "T" for t

A: Given: d=20 mm FS= 1.8 To determine: The minimum failure shear stress