I RevievPart AIf the allowable tensile stress for the bar is(0t)allow = 22.6 ksi, and the allowable shear stressfor the pin is Tallow = 12.2 ksi. Assume the hole inthe bar has the same diameter d as the pin. Taket = 1/4 in. and w = 2 in. (Figure 1)Determine the diameter of the pin so that the load P will be a maximum.Express your answer to three significant figures and include appropriate units.HÀ?d =ValueUnitsSubmitRequest AnswerPart BWhat is this maximum value for P?Express your answer to three significant figures and include appropriate units.Figure1 of 1HA?w/2P =ValueUnitsw/2SubmitRequest Answer

Answered: Image /qna-images/answer/f1043a50-0580-4ed4-bce8-a1f651a7f2c3.jpg

If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress for the pin is Tallow = 12.2 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t= 1/4 in. and w = 2 in. (Eigure 1)

If the allowable tensile stress for the bar is (ot)allow = 22.6 ksi, and the allowable shear stress for the pin is Tallow = 12.2 ksi. Assume the hole in the bar has the same diameter d as the pin. Take t= 1/4 in. and w = 2 in. (Eigure 1)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.10P: A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a...

See similar textbooks

Related questions

Q: The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress…

A: Given data: The side of the hollow square bar is s = 10 in. The thickness of the hollow square bar…

Q: 4. The three steel (E= 29 x 10 psi) eye-bars, each 4 in. by 1.0 in in cross section, are assembled…

Q: PROBLEM 1 Diameter of pin at A = 25 mm Diamcter of cable BC = 10 mm Ultimate shear stress of pin =…

A: Given: dA=25 mmdBC=10 mmτmax=120 MPaσcable=1250 MPa

Q: roblems In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Givenallowable stress of rod σa=86.60MPaallowable shear stress on pin A=60MPadouble shear stress

Q: A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kNm show in…

A: Given:P=400 kNσ=120 MPainside diameter= 100 mm

Q: 3 m Load D 2 m- 3 m The member AC is made from an aluminium alloy and has a rectangular cross…

Q: 1. In the figure shown, determine the diameter of the rod C if the allowable stress 86.60 MPa.…

A: Solution of Question 2

Q: (Q1) A steel tube, 25 mm outside diameter and 12mm inside diameter, cames an axial tensile load of…

Q: A circular tube AB is fixed at one end and free at the other end. The tubeis subjected to axialforce…

A: In this question, we determine the maximum normal stress Maximum normal stress, σ=PA here, P is…

Q: Q5: For the beam ABC which is supported by a pin at (B) and attached to a steel bar at (A).…

Q: The member, shown in the figure, is under tensile load of P=15 kN. The member has uniform thickness…

Q: a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly…

Q: An axially loaded bar has normal stress 173 MPa. The shear stress in the bar is

A: given data : Maximum principal stress (σ1)=173 MPaMinimum principal stress (σ2)=0

Q: he pin as shown in FIGURE G jointed assembly supports a billboard 3 m high x 4 m wide on each end.…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: A cantilevered structure has dimensions L=65-in, L-9.5-in, L=6.2-in, LF3.8-in and diameter d=2.5-in.…

A: Given L1 = 65 in L2= 9.5 in L3 = 6.2 in L4 = 3.8 in d1 = 2.5 in Fy = 78 lb Fz = 153 lb We have to…

Q: An external force P =1800 Ib is applied to the frame shown below via a cable that passes over a…

A: we first have to know the forces acting on the system by drawing FBD of cable pulley system and…

Q: A coil chain of a crane required to carry a maximum load of 50 kN, is shown in Fig. 50 kN 50 kN d-E…

A: Given, Applied load = F = 50 kN = 50,000 N Allowable tensile stress in line stock = σallow = 75 MPa…

Q: A steel plate of dimensions 2.5 × 1.2 × 0.1 m is hoisted by a cable sling that has a clevis at each…

Q: A single shear lap-joint connection is shown in the figure, If P-10,825 N, d-22 mm, and t-38 mm,…

A: Given data P=10.825 Nd=22 mmt=38 mm Here, P is the load, d is the diameter and t is the thickness.…

Q: A lap joint, consisting of 250 mm × 75 mm wooden plates, is fastened with two(2) rows of 20 mm…

A: Width = 250 mm Thickness = 75 mm Diameter of rivet = 20 mm No. of rivets = 6 Shear stress = 70 MPa…

Q: a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3000 lb box beam wall thickness, t = 0.610 in. diameter…

Q: 1. In the figure shown, determine the stress in the cable C if its area is 600 mm². Neglect the…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…

Q: The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness…

A: Solution: The square section is shown below, Outer side length…

Q: The vertical load P acting on the wheel of a traveling crane is 13,000 lb. What is the average shear…

Q: A rigid wheel 1.2 m in diameter is to be provided with a thin steel tyre. If the stress in the steel…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: A link is shown in the figure. If the allowable combined stress at section a-a is limited to 30 ksi,…

Q: A guy wire for an antenna tower is to be alumi- num, having an allowable stress of 12 000 psi. If…

A: Given data as per question Allowable stress = 12000 psi Maximum load = 6400 lb

Q: 1. The homogeneous bar shown in Fig. P-106 is supported by a smooth pin at C and a cable that runs…

A: Given Weight, W = 40 kN Diameter, d = 25 mm = 0.025 m Length, AB = 4 m…

Q: 4. A thin cylinder of inner radius 500 mm and thickness 10 mm is subjected to an internal pressure…

Q: -06 m - 3.1 The rigid bar af negligible weight is supported as shown in the figure If W= 80 kN,…

A: Answer: The temperature change of the assembly that will cause a tensile stress of 50 MPa in the…

Q: Q.1. A. For a hellow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: 1) Given: Outside diameter D2=138mm Inside diameter D1=120mm Maximum tensile stress=115MN/m2 or…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: (a) The stress in bar (1) and bar (2). (b) The load P. (c) The displacement at point A.

A: Given: E1= 100 GPa A1= 520 mm2 E2=70 GPa A2= 960 mm2 F2= 30 kN To determine: The stress in bar 1…

Q: The circular column is subjected to a compressive force of 5kN if the stress in the column is…

Q: A loading condition of a bracket ABCD having a solid cross section is shown below. Given b1 = 3 ft,…

A: (a) Draw the diagram for AB and transfer the load P at point B, It can be seen that a load P and a…

Q: 2.2 in. in.- A IB = in. 1.6 in. e maximum and average stresses in sections A and B, take t = 0.45 in

A: Stress concentration is defined as the localization of high stresses due to the irregularities…

Q: 2. PROBLEM The ratio of diameters for a hollow steel tube is 0.10 which carry a load of 500 kN. If…

A: Given, Ratio of inside diameter to outside diameter = d/D = 0.1 Applied load = P = 500 kN = 500,000…

Q: Asimple pin-connected truss is loaded and supported as shown in the figure. All members of the truss…

Q: 14 The compound bar carries the axial forces P and 2P. Fin lowable value of P if the working…

Q: the right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of…

A: Shear stress is a force that tends to distort a material by causing it to slide along a plane or…

Q: Calculate the average stress in section a-a of the junction shown in the figure when applying force…

A: Let us assume that the diameter of the bolt is d in mm.

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. P-211. Axial loads…

A: Given that: For the composite bar maximum allowable horizontal deformation is 3 mm. It is required…

Q: 120 mm- The thrust bearing supports a load P = 275KN. Find a. The tensile stress in the rod b. The…

Q: A hydraulic press exerts a total load of 5.5 MN. This load is carried by two steel rods supporting…

Q: If the flat link shown below has an allowable tensile stress of 75 MPa, then a force P 1800 N will…

Q: 28. A locomotive coupling rod, 2-5 m between centres, is of symmetrical I- section: the outside…

Q: The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of…

Question

100%

I Reviev
Part A
If the allowable tensile stress for the bar is
(0t)allow = 22.6 ksi, and the allowable shear stress
for the pin is Tallow = 12.2 ksi. Assume the hole in
the bar has the same diameter d as the pin. Take
t = 1/4 in. and w = 2 in. (Figure 1)
Determine the diameter of the pin so that the load P will be a maximum.
Express your answer to three significant figures and include appropriate units.
HÀ
?
d =
Value
Units
Submit
Request Answer
Part B
What is this maximum value for P?
Express your answer to three significant figures and include appropriate units.
Figure
1 of 1
HA
?
w/2
P =
Value
Units
w/2
Submit
Request Answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A solid bar of circular cross section (diameter d) has a hole of diameter d/5 drilled laterally through the center of the bar (sec figure). The allowable average tensile stress on the net cross section of the bar is s allow. (a) Obtain a formula for the allowable load P allowthat the bar can carry in tension. (b) calculate the value of P allowif the bar is made of brass with a diameter d = 1.75 in. and s allow= 12 ksi. Hint: Use the formulas of Case 15. Appendix E.
While drilling a hole with a brace and bit, you exert a downward force P = 25 lb on the handle of the brace (see figure). The diameter of the crank arm is d = 7/16 in. and it s lateral offset is b = 4-7/8 in. Determine the maximum tensile and compressive stresses e1, and e2respectively, in the crank.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A circular aluminum tube with pinned ends supports a load P = 18 kN acting at a distance e = 50 mm from the center (see figure). The length of the tube is 3.5 m, and its modulus of elasticity is 73 GPa. If the maximum permissible stress in the tube is 20 MPa, what is the required outer diameter d2if the ratio of diameters is to be d1/ d2= 0.9?
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?