6 m A cylindrical pressure vessel contains a gas at a pressure of 6.0 MPa. The cylinder, which has an inner radius of 1200 mm and a wall thickness of 20 mm, is fabricated from steel [E = 200GP%; v = 0.30]. The cylindrical portion is 6 m long, ignore the hemispherical end- caps of the tank. corresponding strains in the tank. Using Hooke's Law, determine the MPa Onoop MPа Olong με Elong με Enoop

6 m A cylindrical pressure vessel contains a gas at a pressure of 6.0 MPa. The cylinder, which has an inner radius of 1200 mm and a wall thickness of 20 mm, is fabricated from steel [E = 200GP%; v = 0.30]. The cylindrical portion is 6 m long, ignore the hemispherical end- caps of the tank. corresponding strains in the tank. Using Hooke's Law, determine the MPa Onoop MPа Olong με Elong με Enoop

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.25P: On the surface of a structural component in a space vehicle, the strains arc monitored by means of...

See similar textbooks

Similar questions

A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
A 1.5-m-diameter cylindrical tank is formed of 6-mm-thick sheet steel (E = 200 Gpa, ν = 0.3). The maximum shear strain occurring in this tank when the contents pressure is 1 MPa, is:
1. A steel pipe of length 4 ft, outside diameter of 6.0 in., andinside diameter of 4.5 in., is compressed by an axial forceof 140 kips. The material has a modulus of elasticity of30,000 ksi and Poisson’s ratio of 0.30. Determine thefollowing quantities for the pipe:a. The shortening.b. The lateral strain.c. The percentage increase in the outer and theincrease in the inner diameter.d. The percentage increase in the wall thickness.
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
Pressure inside the cylinder is 10 bars Is this a thin walled cylinder when the thickness is 10 mm. Estimate theoretically the hoop andlongitudinal stresses
A solid homogeneous truss tie-rod has a diameter of 9.52 mm and an original length of 1.75 m experiences a stress of 600 MPa when placed under tension. If the material used for the truss tie-rod has a Young's Modulus, E, of 5.8 x 1011 N/m?, calculate: (i) the tie-rod's extension in millimetres (mm); (ii) the strain energy (U) in Joules; and (ii) the strain energy per unit volume (U/V) in Joules per cubic metre (m³). Give your answers to two decimal places.
Which spring, the truncated cone spring or the helical spring, would have a larger spring constant? Explain.
STRENGTH OF MATERIALS W/SOLUTION 1.) A penstock pipe 10m diameter carries water under a pressure head of 100m. If the wall thickness is 9mm, the tensile stress in the pipe wall is nearest to? A. 2725 B. 1090 C. 545 D. 110 E. NOTA
1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.
specimen of oil having an initial volume of 600 cm3 is subjected toa pressure increase of 3.6 x 106Pa and the volume is found todecrease by 0.45 cm3. What is the bulk modulus of the material?
A cylindrical pressure vessel has an inner diameter of 4 ft and a thicknessof 1 2 in. Determine the maximum internal pressure it can sustain so that neither its circumferential nor its longitudinal stress component exceeds 20 ksi. Under the same conditions, what is the maximum internal pressure that a similar-size spherical vessel can sustain?