6 MN/m 4 MN/m 4 m 2.5 m MN/m
Q: Determine the required strength for LRFD.
A:
Q: Calculate the load distribution of slabs to beams 1, 2 and 3 using 10 kpa load multiplied by the…
A:
Q: A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and…
A: The load is P=10 kN. The length is l=3 m. The cross-sectional area is A=1000 mm2. The modulus of…
Q: A rectangular footing 2.4 m x 3.4 m x 0.33 m thick supports a 300 mm square column at its center.…
A:
Q: A rectangular footing 2 m x 3.6 m x 0.33 m thick supports a 300 mm square column at its center.…
A:
Q: Q2) Calculate the nominal capacity for the section shown if fc'= 6000 Psi and fy=60000 Psi (normal…
A: Considering the above situation As we know T=AsfyAs=4×1=4 in2T=4×60,000=240000 lbT=C1+C2T= due to…
Q: A rectangular footing 2.4 m x 3.1 m x 0.36 m thick supports a 300 mm square column at its center.…
A:
Q: 12. Calculate the equivalent radius (cm) of the resisting section of 20 cm slab, if the ratio of…
A:
Q: calculate Q for transverse shear stress. the rectangle cross-section is hollow with dimensions…
A: Area Above the Neutral axis = 0.5 (6.5x3.5-6x3) =2.375 in2
Q: 1. A 2000-lb wheel load is to be supported by aggregate over soil that can withstand a pressure of…
A:
Q: Given is the 200mm X 400 mm rectangular beam below. 9 kN 7.50 kN/m 400 mm 1.50 kNm 7.50m 200 mm…
A: A loaded beam and it’s cross section is given and it has been asked to determine flexural bending…
Q: A rectangular footing 2 m x 3.3 m x 0.36 m thick supports a 300 mm square column at its center.…
A:
Q: Q1) calculate the nominal capacity for the section If fc'=4000 Psi and fy= 60000 Psi (normal weight…
A: Given: fc'=4000 Psi=27.579 N/mm2fy=6000 Psi=41.368 N/mm2
Q: Q10. For the beam shown below, determine the design shear strength contributed by concrete (4Vc) and…
A: Given:- The stirrups used are No. 3 at 6 in spacing The magnitude of the factored shear force = 60…
Q: Determine the maximum live load that can be applied on one way slab shown in Fig. (1). The slab is…
A: One way slab Because of its geometry, the one-way slab is a slab that is supported by parallel walls…
Q: You are a structural Engineer who works in Dar Al Handasah company. Your direct manager has called…
A: Hi there!! Since you have posted a question with multiple sub-parts, we will solve the first three…
Q: 0.5 W 0.5 W fo = 30 MPa fy = 414MPa 8. 250 mm 250 mm 3.5 m 3.5 m 2- 25mm Ø 3-36mm Ø 250 mm 300 mm
A:
Q: A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The…
A:
Q: 2.A timber block 250 mm square is reinforced on each side by a steel plate 250 mm wide and t mm…
A:
Q: Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc=50Omm,…
A:
Q: Define Load Combinations for ASD
A: Answer Introduction ASD ASD represents the allowable stress design ASD consists of the load…
Q: Example 3 Estimate the steel reinforcement for the Column as Shown in figures below $-010mme10am…
A: To find the total amount of steel required in the column Longitudinal reinforcement= 8 bars of 16…
Q: From given Fence plan and its section below, fill up given table below of Abstract Estimation for a…
A: Load bearing type structure A load-bearing structure is one in which loads are carried from the…
Q: STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be…
A:
Q: Draw the figure and show complete solution. A rectangular beam is 10 in. wide and has an effective…
A:
Q: First Grading Problem Solving Determine the magnitude and location of the Resultant from the fixed…
A: Given data:
Q: Submit your question to our 24/7 subject matter experts with Masters and PhDs and get a solution in…
A:
Q: 2. Problem 4: Calculate the nominal strength of the section. 2.25 f 3,000 psi 2.50" #9 BARS Grade 60…
A:
Q: Part A The box girder is subjected to a shear of V = 16.6 kN. (Eigure 1) Determine the shear flow at…
A: Given:- The magnitude of the shear force on the box girder = V = 16.6 kN To determine:- a) The shear…
Q: Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc=50mm,…
A:
Q: A 50 meter steel tape is suspended in the air between a transit and a vertical rod which is placed…
A: If the sag correction is neglected there will be only slope correction:cslope=l1-cosθθ=1°30'
Q: 2. A concrete beam is shown below. A. Determine the magnitude of the resultant force acting on the…
A:
Q: 4.2. Using the coefficient method, design a (case 3) cantilever slab (thickness and reinforcements)…
A: L1=4m L2=3m LL=6.69kPa DL=2.5kPa fc=21MPa fy=276MPa
Q: Question 2: For the reinforced concrete structural plan shown in figure, it is required to: >…
A: Consider the free body diagram;
Q: Determine the dead weight of the reinforced concrete T-beam bridge interior beam using Figure 26 and…
A: The dead weight of bridge will include the dead weight of concrete mainly. Wearing surface load on…
Q: A 500-N concrete block is to be lifted by the pair of tongs shown. 500 N 45 mm T45 mm 90 mm 90 mm A…
A:
Q: By Khosla method, the approximate chickness under the gate equal to
A: Given:- h=3mTo find:-approximate thickness under the gate
Q: P/A and (oalalow MJAr? (os)aller 54000 If it is pinned at its top and bottom, and a compressive load…
A: Solution Given that (σb)allow=21 ksi
Q: rectangular footing 2.3 m x 3.3 m x 0.31 m thick supports a 300 mm square column at its center.…
A:
Q: gram for MD and
A: A shear force diagram depicts the variation in shear force over a beam's length. The total of…
Q: A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The…
A:
Q: Given a 300mm by 500mm concrete beam loaded(factored) as shown, reinforced with 4-25mm deformed…
A: The moment is the amount of crack that happens due to load, or the effect of the load on the…
Q: Given the following rectangular (35 ft x 45 ft) two-story warehouse and loading shown, determine the…
A: Given: warehouse area = 35 x 45 = 1575 ft2 Floor: DL = 65 lb/ft2 LL = 250 lb/ft2 Roof: DL = 55…
Q: Refer to the beam loaded as shown. What is the value of Ay?
A: Take equilibrium about y:∑ Fy=0
Q: 2 Ib/ft 3.5 lb/ft - 2.75 ft -4 ft - 1.5 ft
A: Varignon theorem: Varignon's theorem states that when the moment of a resultant of two forces about…
Q: A typical grade beam 300 x 800 is reinforced with 2- 25M bars and the cover is forconcrete cast and…
A: D (overall depth) = 800mm d' (effective cover) = 60mm d (effective depth) = 740mm b (width) = 300mm…
Q: A 40-1b roller, of diameter 8 in., which is to be used on a tile floor, is resting directly on the…
A: Energy is defined as an external cause that changes or tends to change the state of the body when it…
Q: Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc=50mm,…
A:
Step by step
Solved in 2 steps with 2 images
- Two forces act on the screw eye. If F1 = 400 N andF2 = 600 N, determine the angle θ (0° ≤ θ ≤ 180°) betweenthem, so that the resultant force has a magnitude ofFR = 800 N.Determine the moment of this figure P1=35kN and P2=55kNThe Q-kg industrial door with mass center at G is being positioned for repair by insertion of the 5° wedge under corner B. Horizontal movement is prevented by the small ledge at corner A. The coefficients of static friction at both the top and bottom wedge surfaces are 0.66. Calculate the rightward force P' which would remove the wedge from under the door. Assume that corner A does not slip for your calculation of P'. Q = 402
- The water-supply tank has a hemispherical bottom and cylindrical sides. Determine the weight of water in the tank when it is filled to the top at C. Take γw = 62.4 lb/ft3.c. Slope at L/3. d. Deflection at L/3Properties: • b1 = 300 mm • b2 = 180 mm • d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa • fy = 414 MPa • eccentricity = 200 mm Determine the following: 1. Location of the plastic centroid measured from the y-axis in mm 2. Depth of the compression block in mm 3. Nominal Axial in kN 4. Moment Capacity in kN-m
- Given P1=00K P2=19K UNKNOWN: 1. FORCE IN MEMBER GF 2. FORCE IN MEMBER FC 3. FORCE IN MEMBER CDThe 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?The 450N plate is attached to collars which may slide on the vertical rod. If the coefficient of static friction is 04 between both collars and the rod determine the maximum supporting force available from friction when F = 0 and when F = 200N; a = 2.75m , b = 4.5m , c = 2m Show solution, the answer is 618.75
- determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal placesQ5. Crank OA Rotates With Uniform Angular Velocity 0, = 4 Rad/s Along Counterclockwise. Take OA= = 0.5 M, AB=2r, And BC = V2r. For The Instant, P=45, OA Is Horizontal And AB Is Vertical. Determine The Angular VelocityThe slotted arm OA rotates about a fixed axis through O. At the instant under consideration, θ = 32°, θ˙ = 47 deg/s, and θ¨ = 21 deg/s2. Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.3-kg slider B. Neglect all friction, and let L = 0.64 m. The motion occurs in a vertical plane.