6 Ohm 1 mH 18 VI50 Hz/0 Deg 3 A/50 Ha0 Deg 1 uF Ohm Fig.2 Tablel Measured values Zth Eth Itoad Calculated values Zth Itoad Discussion 1. Calculate thevenin impedance Zth and record the value in table 1 2. Calculate thevenin voltage source Eth and record the value in tablel 3. Calculate the current through the load 22 resistance then record the value in table 1 4. Discuss the result.

6 Ohm 1 mH 18 VI50 Hz/0 Deg 3 A/50 Ha0 Deg 1 uF Ohm Fig.2 Tablel Measured values Zth Eth Itoad Calculated values Zth Itoad Discussion 1. Calculate thevenin impedance Zth and record the value in table 1 2. Calculate thevenin voltage source Eth and record the value in tablel 3. Calculate the current through the load 22 resistance then record the value in table 1 4. Discuss the result.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

10 What is the value of phase voltage, when, three loads, each of resistance 11 Ω are connected in star to a 435 V, 3-phase, 50 Hz supply? a. 145.00 V b. 251.15 V c. 753.42 V d. 1305.00 V
The values of the circuit elements are given below.Accordingly |I| What is its value (the maximum value of its current)? V=110 phase 40 VR1=10 ohmsR2=12 ohmsR3=14 ohmsL1=j15 ohmsL2=j8 ohmsM=j15 ohmsC1=-j5 ohmsC2=-j12 ohms
A load consists of R=99 , XL=52 and XC=30 . All the elements are connected in parallel across 140 Volt supply. Find the values of real power delivered, reactive power and apparent power. (i) Real Power, P= Answer for part 1 (ii) Reactive Power, Q= Answer for part 2 (iii) Apparent Power, |S|= Answer for part 3
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5 + j4) ohms, Z2 = 10 bar angle of -30° ohms, and Z3 = 15e j0.758 ohms, calculate the currrent flowing in each resistor. Use Nodal analysis.
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected inseries with the supply voltage V1 while the impedance Z2 is connected in series with the voltageV2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angleof 15° ohms, calculate the currrent flowing in each impedance. Use Nodal analysis.
Three impedances Z1, Z2 and Z3 are connected in tee. The impedance Z1 is connected inseries with the supply voltage V1 while the impedance Z2 is connected in series with the voltageV2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and Z3 = 15 bar angleof 15° ohms, calculate the currrent flowing in each impedance. Use Superposition theorem.
An inductive reactance of 8 ohms is connected in parallel with a capacitive reactance of 18 ohms; this combination is then connected in series with a variable resistance. For wht value of resistnace will the power factor be 0.5, and what current and power will the circuit take if the impressed emf is 118 volts.
Current | I | What is the value (maximum value of the current)?Values of circuit elements:V= 120 phase 50 VR1= 5 OhmsR2= 12 OhmsR3= 12 OhmsL1= j10 OhmsL2= j10 OhmsM= j13 OhmsC1= -j17 OhmsC2= -j17 Ohms
Three impedances Z1, Z2 and ZL are connected in tee. The impedance Z1 is connected in series with the supply voltage V1 while the impedance Z2 is connected in series with the voltage V2. If V1 = 200 volts, V2 = 120 volts, Z1 = (5+j4) ohms, Z2 = (10-j13) ohms, and ZL. Calculate the maximum power transferred to load impedance ZL . Use Maximum power transfer theorem.
The power customer has four circuits of220-volt three phase. The circuits have the maximum demand as follows: Circuit no 1 = 35 Amperes Circuit no 3 = 72 Amperes Circuit no 2 = 46 Amperes Circuit no 4 = 57 Amperes The diversity factor is 1.5, the load factor is 50% and the power factor is 80%. Determine the maximum KVA demand of the customer? A. 46 B. 80 C. 26.5 D. 53 The answer here is letter D but I dont know its solution
Electrical Circuits (a) the relationship between line and phase voltages of a 4-wire STAR resistive balanced load (b) the relationship between line and phase currents of a 4-wire STAR resistive balanced load (c) the phasor diagram of a 4-wire STAR resistive balanced load.
an R-L circuit takes a current of 7amp that lags behind the 231-volt source by 35elec deg. calculate the power factor, power, impedance, resistance, and inductive reactance of the circuit.