Air enters a 12-cm-diameter adiabatic duct with inlet conditions of V1 = 150 m/s, T1 = 500 K, and P1 = 200 kPa. For an average friction factor of 0.014, determine the duct length from the inlet where the inlet velocity doubles. Also determine the pressure drop along that section of the duct.

Q: In fully developed laminar flow in a circular pipe, the velocity at R/2 (midway between the wall…

A: Given : The velocity at r from the center line, V r =13 m/s here, r=R/2

Q: 1. The water in a 6-m-diameter, 2-m-high above-ground swimming pool is to be emptied by unplugging a…

A:

Q: Water at 10°C (? = 999.7 kg/m3 and ? = 1.307 × 10−3 kg/m·s) is flowing steadily in a…

A: The temperature of water is T = 10°C = (10°C + 273) K = 283 K The density of water ρ = 999.7 kg/m3…

Q: A U-tube open at both ends is partially filled with water. Oil having a density of 750 kg/m3 is then…

A:

Q: Oil at 20°C is flowing through a vertical glass funnel that consists of a 20-cm-high cylindrical…

A: Given: The diameter of pipe = 1 cm The height of cylindrical reservoir = 20 cm The height of the…

Q: Oil with ? = 876 kg/m3 and ? = 0.24 kg/m·s is flowing through a 1.5-cm-diameter pipe that discharges…

A: Given data Determine the flow rate of oil through the pipe if the pipe is (a) horizontal (b)…

Q: A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and…

A: Write the given data. Write the properties of air at 20°C.

Q: Steam at 0.7Mpa and 250'c expands in a nozzle to 0.1Mpa. Determine the throat and nozzle exit cross…

A:

Q: A 3.5 m-diameter tank is initially filled with water 2.25 m above the center of a sharp-edged…

A:

Q: Heated air at 1 atm and 30∘∘C is to be transported in a 150-m-long circular plastic duct at a rate…

A:

Q: A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the…

A:

Q: The fluid condition at the Inlet and exit of a horizontal convergent nozzle is analysed. The nozzle…

A: Inlet velocity:- 289km/hr                        = 80.27 m/s  Inlet area = 0.24 m² Specific volume…

Q: water at 4-degree centigrade ( ρ=998 kg/m3 and μ=1.52 *10-3pa.s) is flowing steadily through a 3mm…

A: Given data:

Q: Ol at 20°C (p = 888.1 kg/m² and u = 0.8374 kg/m - s) is flowing steadily in a 1.25 cm-diameter,…

A:

Q: The compressed air requirements of a manufacturing facility are met by a 120-hp compressor that…

A: Given data as per question Length of pipe = 9m Diameter of pipe = 22 cm = 0.22 m Flow rate = 0.27…

Q: A very large tank contains air at 102 kPa at a location where the atmospheric air is at 100 kPa and…

A: Pressure of air in the tank Pa = 102 kPa Atmospheric pressure, Patm = 100 kPa Temperature, T= 20°C…

Q: The power available in a jet having a cross-sectional area of 0.005 m2 with a velocity of 25.8 m/s

A:

Q: A 3-m-diameter tank is initially filled with water 2 m above the center of a sharp-edged…

A: Given data

Q: What are the primary differences between fans, blowers, and compressors? Discuss in terms of…

A: The head or pressure producing machines increases the level of energy of the fluids passing through…

Q: The water at 20°C in a 10-m-diameter, 2-m-high aboveground swimming pool is to be emptied by…

A: Given Data: The temperature of water is T = 20°C. The diameter of pool is D = 10 m. The height of…

Q: In fully developed laminar flow in a circular pipe, the velocity at R/2 (midway between the wall…

A: Given data as per the question the velocity at R/2 = 11 m/s

Q: Air flows through a nozzle from a large vessel in which the pressure and temperature are 500 kPa and…

A:

Q: Air enters a 10-m-long section of a rectangular duct of cross section 15 cm × 20 cm made of…

A: Given data P1=1 atmT1=35°cV=5 m/s

Q: The velocity profile in a fully developed laminar flow of water at 40°F in a 250-ft-long horizontal…

A: Solution : The equation of the velocity profile in a fully developed laminar flow is given as : The…

Q: Air at 100 kPa and 25°C flows in a horizontal duct of variable cross section. The water column in…

A: Given : The pressure inlet = 100 kPa The air temperature = 25°C The difference in the height of…

Q: what is the jet velocity?

A:

Q: The water at 20°C in a 10-m-diameter, 2-m-high aboveground swimming pool is to be emptied by…

A: Write the properties of water at 20°C. Write the value of the roughness of the pipe.

Q: The air in a 5-m × 5-m × 3-m hospital room is to be completely replaced by conditioned air every 15…

A: Given: The time of the air replacement is t=15 min. The average air velocity in the duct is v=5 m/s.…

Q: The velocity profile in fully developed laminar flow in a circular pipe of inner radius R = 2 cm, in…

A: Given data: The inner radius is, R = 2 cm. Velocity profile, u(r) = 4(1 – r2/R2). Write the…

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Given: The value of volumetric flow rate at the inlet is, Qin=0.6 m3s. The diameter of the…

Q: Air flows steadily and isentroplcally into an aircraft inlet at a rnass flow rate of 100 kgs·1• At a…

A: Given data: The mass flow rate is m˙=100 kg/s The area at the inlet is A1=0.5 m2 The inlet…

Q: Combustion gases with an average specific heat ratio of k=1.33 and a gas constant of R=0.280 kJ/kgK…

A: Write the given information.

Q: On a T-s diagram of Fanno flow, what do the points on the Fanno line represent?

A: Fanno flow: Fanno flow flows through the duct in which the friction forces are taken into…

Q: Air enters a compressor at a temperature of 70•C and a pressure of 10 kPa. At the exit of the…

A:

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Properties of air at 60 degrees Celsius are: The roughness of the galvanized steel pipe is Given…

Q: Consider the flow of air over the wings of an aircraft. Is this flow internal or external? How about…

A: Internal flow –when the flow is completely bounded by the surface then this type of the flow is…

Q: The compressed air requirements of a textile factory are met by a large compressor that draws in 0.6…

A: Properties of air at 60 degrees Celsius are: The roughness of the galvanized steel pipe is Given…

Q: Argon gas enters a constant cross-sectional area duct at Ma1 = 0.2, P1 = 320 kPa, and T1 = 400 K at…

A: Given data M1=0.2P1=320 kPaT1=400 K

Q: Air enters a 5-cm-diameter, 4-m-long adiabatic duct with inlet conditions of Ma1 = 2.8, T1 = 380 K,…

A: Take the properties of air to be k = 1.4, cp = 1.005 kJ/kg-K, and R = 0.287kJ/kg-K. The average…

Q: - Air at 105 kPa and 37°C flows upward through a 6-cm-diameter inclined duct at a rate of Q (L/s).…

A:

Q: Q1: Air at 35 °C enters a 7-m-long section of a rectangular duct of cross section 15 cm x 20 cm made…

A:

Q: Air enters a 7-m-long section of a rectangular duct of cross section 15 cm × 20 cm made of…

A:

Q: Which has a greater minor loss coefficient during pipe flow: gradual expansion or gradual…

A: Which has a greater minor loss coefficient during pipe flow: gradual expansion or gradual…

Q: Air in a room at T0= 290 K and P0= 95 kPa isdrawn steadily by a vacuum pump through a…

A:

Q: Define mass and volume flow rates. How are they related to each other?

A: Mass Flow rate⇒Mass flow rate is defined as the mass of fluid flowing per unit time. Mass flow rate…

Q: Water at 75 degrees Celsius is flowing horizontally at a rate of 1.6 m^3/min in a pipe. It enters a…

A:

Q: The liquid storage tank shown in Fig has two inlet streams with mass flow rates w1 and w2 and an…

A: Given that, Height of storage tank, h=2.5 m,Diameter of storage tank, D=2 m,Density of liquid, ρ=800…

Q: Air is flowing through a venture-meter whose diameter is 2.6 in at the entrance part (location 1)…

A: Given Data: The diameter at the entrance is, d1=2.6 in. The diameter at the throat is, d2=1.8 in.…