Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the tower at 43.5°C. The air enters the tower at 18.5°C and 60% R.H. and leaves the tower at 27°C and in saturated condition. The motor driven fan forces 600m² of air per minute through the tower while using 4kW of power. Determine: (1) Temperature of the water coming out of the tower. Makeun water required per hour G

Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the tower at 43.5°C. The air enters the tower at 18.5°C and 60% R.H. and leaves the tower at 27°C and in saturated condition. The motor driven fan forces 600m² of air per minute through the tower while using 4kW of power. Determine: (1) Temperature of the water coming out of the tower. Makeun water required per hour G

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A three-stage compressor receives 500 lps of air at 101 kPaa and 27 oC, anddischarges at 750 kPaa. Determine a) the power required; b) the pressure at eachintercooler; c) the maximum temperature; and d) the heat transferred in each intercooler.e) What is the discharge temperature of a single-stage compressor operating at the same intake and discharge temperatures?
5.) By traveling through a bass tube, 2.5 cm O.D. and 2.2 cm I.D., which is surrounded by steam at 55 kPa and 90% quality, 9.4 kg/s of water is heated from 15oC to 60oC. Assume the inside unit convective coefficient is 2000 W/m2-K, and the outside unit convective coefficient is 7950 W/m2-K. Determine (a) the length of tube required; (b) the steam supply in kg/h if no subcooling occurs.
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
A three-stage compressor receives 500 lps of air at 101 kPaa and 27degrees Celcius, anddischarges at 750 kPaa. Determine a) the power required; b) the pressure at eachintercooler; c) the maximum temperature; and d) the heat transferred in each intercooler. e) What is the discharge temperature of a single-stage compressor operating at the sameintake and discharge temperatures?
Consider a gas turbine of 200 kJ/kg net work, operating under standard cold air assumptions. Determine the thermal efficiency, in %, of the turbine, if it has a regenerator with 90% efficiency.
Air enters a two-stage compressor at 100kpa and 27 C and is compressed to 900kpa. The pressure ratio across each stage is the same and the air is cooled to the initial temperature between the two stages. Assuming the compression process to be isentropic, determine the power input for a mass flow rate of 0.03kg/s. what would the power input be if only one stage of compression was used?
An isobaric boiler vaporizes saturated liquid water at 200kPa until it is saturated vapor. If the mass flowrate of the water is increased but the same heat transfer rate is maintained, what should be the new state of the boiler outlet? a. Subcooled liquid b. Superheated vapor c. Mixture of liquid and vapor d. Saturated vapor
The kinetic energy of a fluid increases as it is accelerated in an adiabatic nozzle. Where does this energy come from? Explain (in brief) using the appropriate equation. An ideal gas enters an adiabatic, horizontal, nozzle (fixed on the ground) at 300 kPa, 200°C and 30 m/s, and leaves at 100 kPa and 180 m/s. These conditions are maintained for all time. The inlet area of the nozzle is 80 cm2. Determine (a) the mass flow rate of gas through the nozzle, (b) the exit temperature ofgas, and (c) the exit (outlet) area of the nozzle. Given: gas constant is 0.287 kPa.m3/(kg.K) ; average value of specific heat capacity of gas (cp, avg) is 1.02 kJ/(kg . ºC)
Air with mass flow rate of 1 kg/s enters the first stage of a compressor at 100 kPa and 300 K and exit the second stage of the compressor at 2677 kPa. If the compressed air outgoing from the first stage of the compressor passes through an intercooler, then enters the second stage of the compressor at temperature 353 K. What is the indicated isothermal efficiency for the compressor assuming ideal compression process with polytropica index n = 1.3 for both stages, no pressure loss in the intercooler, and the pressure ratio across the first and the second stage of the compressor are equal?
A steady-flow thermodynamic system receives 100 lb/min of fluid at 30 psia and 200 Fahrenheit and discharges it from a point 80 ft above the entrance section at 150 psia and 600 Fahrenheit. The fluid enters with velocity of 1200 fpm and leaves with a velocity of 200 fpm. During this process, there are supplied 25,000 Btu/hr of heat from an external source and the increase in enthalpy is 2 Btu/lb. Determine the work done in horsepower.
he refrigerant R-134a enters the compressor of a refrigeration machine at a pressure of 140kPa and a temperature of -10°C, and exits at a pressure of 1MPa. The volumetric flow of the refrigerant entering the compressor is 0.23m3/minute. The refrigerant enters the throttling valve at a pressure of 0.95MP and at 30 °C, and exits the evaporator as saturated steam at -18 °C. The adiabatic efficiency of the compressor is 78%. Show the cycle in the T-s diagram. a) Power required to start the compressor b) Calculate the heat withdrawn from the cooled environment in unit time, COPSM=? c) Calculate how much the pressure of the refrigerant drops between the evaporator and the compressor and how much the heat gain is.
Question 2 Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 5 MPa, 600°C, and 90 m/s, and the exit conditions are 50 kPa, 90 percent quality, and 55 m/s. The mass flow rate of the steam is 14 kg/s. Determine: 2.1 The turbine inlet area, and 2.2 The power output in MW.