6.The dimensions of the various links of aFig. 7.35mechanism, as shown in Fig. 7.36, are asfollows :AB= 30 mm; BC= 80 mm; CD= 45 mm ; and CE = 120 mm.30°A75 mm22.5 mmEFig. 7.36The crank A B rotates uniformly in the clockwise direction at 120 r.p.m. Draw the velocity diagram forthe given configurativelocities of the links BC, CD and CE.of the mechanism and determine the velocity of the slider E and angularAlso draw a diagram showing the extreme top and bottom positions of the crank DC and the corre-sponding configurations of the mechanism.Find the length of each of the strokes.[Ans. 120 mm/s; 2.8 rad/s; 5.8 rad/s; 2 rad/s ; 10 mm ; 23 mm]

Answer: To find: Velocity of E and angular velocity of links BC, CD and CE

Answered: 6. The dimensions of the various links…

6. The dimensions of the various links of a Fig. 7.35 mechanism, as shown in Fig. 7.36, are as follows : AB = 30 mm ; BC- 80 mm; CD = 45 mm ; and CE= 120 mm. B. 30 75 mm 22.5 mm E Fig. 7.36

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As a young engineer, you have been tasked to select the location of a wind turbine based on the details of the location and relevant specification below:Air densityAverage air velocityDiameter of wind turbine bladesLOCATION A1.29 kg/m3 54 km/h 70 mLOCATION B1.21 kg/m3 63 km/h 60 m By comparing the amount of power generated (in MW) at Location A and Location B, determine the location that will give the optimum wind power generation.9 kg of Refrigerant 134-a is initially at 26.69°C with enthalpy of 100 kJ/kg. Heat is transferred to the refrigerant under a constant-pressure process until the entropy of the refrigerant reaches 0.9795 kJ/kg.K.(i) Determine the final temperature of the refrigerant(ii) Calculate the boundary work, Wb, in kJ.Assist your answer with a proper P-v diagram indicating the properties,process, and boundary work region clearly.(iii) Explain the reason behind the high amount of boundary work obtained in (ii).Assist your explanation with relevant sketching.
At a hydraulic plant the propeller type turbine are rated at 48,000 HP at 82 rpm under a 14 meters head, the diameter is 7 meters, for a geometrical similar turbine to develop 36,000 HP under a 11 meters head. After resolving the percentage change in probable flow, determine the following: (A) What diameter, in meter, of the impeller to be used? (B) What is the speed, in RPM, should be used?
Example 1.10 gave an analysis that predicted that theviscous moment on a rotating disk M = πμ V R 4 /(2 h ). Ifthe uncertainty of each of the four variables ( μ , Ω,, R , h )is 1.0 percent, what is the estimated overall uncertaintyof the moment M ?( a ) 4.0 percent ( b ) 4.4 percent ( c ) 5.0 percent( d ) 6.0 percent ( e ) 7.0 percent
For a high-fl ow site with a head of 45 ft, it is desired to designa single 7-ft-diameter turbine that develops 4000 bhp at aspeed of 360 r/min and 88-percent effi ciency. It is decidedfi rst to test a geometrically similar model of diameter 1 ft,running at 1180 r/min. (a) What likely type of turbine is inthe prototype? What are the appropriate (b) head and(c) fl ow rate for the model test? (d ) Estimate the powerexpected to be delivered by the model turbine.
Note: Don't copy from other experts solution. Read the question carefully and give me right solution with clear calculations. The absolute velocity of a jet of steam impinging on the blades of a steam turbine is 2,200 ft/sec, and that leaving is 980 ft/sec. Assume α1 = 10°, α2 = 155° , u1 = 36 ft/sec, u2 = 72 ft/sec, and r1 =4-inches, r2 = 8-inches. Knowing that the density times flow rate, ρQ = 0.0122 slugs/sec, what is the Power delivered, in HP?
13.73. A model of a motorboat is driven at 4.57 m/s by means of a jet of water 25 mm in diameter, ejected directly astern. The velocity of the jet relative to the model is 35.1 m/s. What is the driving force? Ans. 543 N
Air at 60∘C∘C flows through the very wide duct. Suppose that L� = 150 mmmm . ν� = 18.9(10−6−6) m2/sm2/s. (Figure 1) Determine the required dimension a� of the duct at x� = 4 mm so that the central core flow velocity maintains the constant free-stream velocity of 0.5 m/sm/s. Express your answer to three significant figures and include the appropriate units.
A Kaplan turbine has the following specifications: H =25 ft., N=400 rpm; power = 650 hp. If the efficiency of the unit is 90%, estimate (a) the flow rate, (b) approxi-mate diameter of the runner, (c) turbine setting to avoid cavitation if the location is at sea level, and (d) turbine setting to avoid cavitation if the location of the unitis at an elevation of 5000 ft. The local temperature is 60°F.Ans: (a) Q=254 cfs; (c) Hs=5.8 ft.; (d) 0.12 ft.
The dimensions of a Francis radial-flow hydroturbine are r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m, where location 2 is the inlet and location 1 is the outlet. At the turbine inlet and outflow, the runner blade angles are β2 = 71.4° and β1 = 15.3°, respectively. The runner rotates at a rate of ń = 160 rpm. At design conditions, the volume flow rate is 80.0 m3 /s. (a) State the necessary assumptions and calculate the angle α2 at which the wicket gates should turn the flow (Figure Q1), with α2 measured from the radial direction at the runner inlet. (b) Calculate the swirl angle α1 (Figure Q1), where α1 is the angle measured from the radial direction at the runner output. (c) Calculate the needed net head and power output. (d) Discuss the actual power output and head required for actual case of the turbine (irreversibility not neglected). (Properties For water at 20oC, ρ = 998.0 kg/m3)
A radial flow pump whose 100-mmmm-diameter impeller rotates at 120 rad/srad/s discharges water at 0.25 m3/sm3/s. Determine the discharge of a geometrically similar pump having a 155-mmmm-diameter impeller that rotates at 90 rad/srad/s. Express your answer to three significant figures and include the appropriate units.
A Francis radial-flow hydroturbine has the following dimensions, where location 2 is the inlet and location 1 is the outlet: r2 = 2.00 m, r1 = 1.30 m, b2 = 0.85 m, and b1 = 2.10 m. The runner blade angles are ?2 = 71.4° and ?1 = 15.3° at the turbine inlet and outlet, respectively. The runner rotates at n. = 160 rpm. The volume flow rate at design conditions is 80.0 m3/s. Irreversible losses are neglected in this preliminary analysis. Calculate the angle ?2 through which the wicket gates should turn the flow, where ?2 is measured from the radial direction at the runner inlet. Calculate the swirl angle ?1, where ?1 is measured from the radial direction at the runner outlet. Does this turbine have forward or reverse swirl? Predict the power output (MW) and required net head (m).
(Combine Rankine Cycle) Show the details of your solutions with TS Diagrams with correct dimension analysis