6.1 Dj and D2 are the inlet and outlet diameters of the pipe connected to the water turbine shown in the figure. The gage pressure at the inlet and outlet of the turbine are p1 and p2. The elevation difference between the pipe inlet and outlet is h. If the water flow rate is Q and the total frictional losses is H1. Determine the mechanical power delivered by the turbine if it is 90% efficient. 1 Turbine, h D2 Dj = 320 mm D2 = 160 mm h = 45m P1 =10.5bar %3D P2 =5.5 bar Q = 0.065 m³.s HL =8.0 m

6.1 Dj and D2 are the inlet and outlet diameters of the pipe connected to the water turbine shown in the figure. The gage pressure at the inlet and outlet of the turbine are p1 and p2. The elevation difference between the pipe inlet and outlet is h. If the water flow rate is Q and the total frictional losses is H1. Determine the mechanical power delivered by the turbine if it is 90% efficient. 1 Turbine, h D2 Dj = 320 mm D2 = 160 mm h = 45m P1 =10.5bar %3D P2 =5.5 bar Q = 0.065 m³.s HL =8.0 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The figure shows a pump that draws 840 L/min of crude oil (s= 0.85) in an underground storage drum to the first stage of a processing system; a) If the total energy loss in the system is 4.2 N m/N of oil flow, determine the power transmitted by the pump to the fluid. b) If the energy loss in the steel suction line is 1.4 N m/N of oil flow, determine the pressure at the pump inlet
The water is flowing through a pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 6 m above datum and section 2 is 4 m above datum. If the pressure at section 1 is 39.24 N/cm2, find the intensity of pressure at section 2. Sketch the arrangement.
The turbine in the figure uses the flow of the river channeled under the dam, as shown. The friction losses of the system are hf=3.5V^2/(2g), where V is the average velocity in the inlet duct. For what flow in m^3/s would power of 25 MW be extracted? Which of the two solutions has a better "conversion yield"?
Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from Ato B is 5 cfs. a) Determine the head loss in feet in PIPE 1 and PIPE 2 b) Determine the head loss in feet in PIPE 5 c) Determine the flow in the upper branch pipe Q2 in cubic feet per second d) Determine the total head loss in feet between the inlet A and the outlet D
1. Water from a reservoir passes over a dam through a turbine and discharges from a 60-cm ID pipe at a point 40 m below the reservoir surface. The turbine delivers 1 MW. a. Draw the system and write the relevant form of the mechanical energy balance. b. Calculate the required flow rate of water in m3/min if friction is neglected. (Note: The equation you will solve in this problem has multiple roots. Find a solution that is physically relevant.) c. If friction were included, would a higher or lower flow rate be required?
A 20-KW motor with 80% efficiency drives a centrifugal pump delivery 0.08m3/sec against a head of 20m. Determine the pump efficiency
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
Given: Two(2) identical pumps series in connection Suction Pressure = 3.2 Bars Discharge Pressure = 4.95 Bars Suction Pipe Dia = 450mm Discharge pipe Dia = 480mm Velocity of Water = 4.25 m/s Solve: Total Head, Pump1 & 2 individual head and if Pump 2 is 9.5% less than Pump 1 and Or = Total Flow Rate
2. A hydro-electric plant having 50 km2 reservoir area and 100 m head is used to generate power. The energy utilized by the consumers whose load is connected to the power plant during a five hour period is 13.5 x 106 kW-hr. The over-all generation efficiency is 75 %. Find the fall in the height of water in the reservoir after the 5 hour period. show Complete Solution/s (i.e. transformations, equivalent formula, etc).
Include a free body diagram A pump is installed in a pipe system, where at the suction side 1.0 m below the pump, an open manometer reads a vacuum of 20 cm of mercury. The pipe is 10 cm in diameter and the flow is 35 L/s of water. Find the total energy at the location of the manometer, relative to a datum, through the pump. A. 12.74 m B. -4.67 m C. 2.56 D. -2.72 m
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction.
Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside area of . The exit nozzle at point F has an inside area of . The distances are , , and , respectively. Find the pressure at point D_______ A. 5.74 kPa (gage) B. -5.74 kPa (gage) C. 5.74 kPa (absolute) D. -5.74 kPa (absolute)