Q2. The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 m /s. The head loss across the turbine from section 1 to section 2 is negligible, but the head loss for entire flow is 2.9m. Determine: a. The pressure difference across the turbine, P1- P2, across the turbine. b. The elevation h P1- 60 psi O - 150 ft3/s Di - 3 t Section (1). Turbine Figure 2 10 ft P2 - 10 in. Hg vacuum D2 - 4 ft Section (2) Page 1 of 2

Q2. The turbine shown in figure 2 develops 3000 kW when the water flowrate is 24 m /s. The head loss across the turbine from section 1 to section 2 is negligible, but the head loss for entire flow is 2.9m. Determine: a. The pressure difference across the turbine, P1- P2, across the turbine. b. The elevation h P1- 60 psi O - 150 ft3/s Di - 3 t Section (1). Turbine Figure 2 10 ft P2 - 10 in. Hg vacuum D2 - 4 ft Section (2) Page 1 of 2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A pump draws water from a lake delivered to a height of 50 meters above the lake and encounters 15 meters of headloss. Determine the pump power requirement in Kilo-Watts to deliver a constant supply of 500 Liters per second? The correct answer has a margin of 1 from exact answer. Velocity head is neglected.
In the pumping system shown below, determine the following. a. Head loss at suction in m b. Head loss at discharge in meters c. Total head losses in meters d. Total dynamic head developed by the pump in meters e. Water Power in KW f. Brake Power in KW g. Energy consumption for 15 hours operation in KW-hr h. Line current drawn by the 3-Phase motor drive in amperes i. Pumping cost in Pesos/Day if electricity costs P7.00/KW-hr Figure: Other Data Water Temperature: 20∘C Suction Line 5−20 m 1−90∘ Elbow 1− Check Valve (Fully Open) Pipe Material: Galvanized Iron ND=100 mm Discharge Line L=50 m 12−90∘ Elbow 1− Gate Valve (Fully Open) 1− Check Valve Pipe Material: Galvanized Iron ND =80 mm Pump Efficiency: 75% Motor Efficiency: 82% Volts: 220 V Power Factor: 92%
Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from Ato B is 5 cfs. a) Determine the head loss in feet in PIPE 1 and PIPE 2 b) Determine the head loss in feet in PIPE 5 c) Determine the flow in the upper branch pipe Q2 in cubic feet per second d) Determine the total head loss in feet between the inlet A and the outlet D
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
A pump has a head of 20m at 450rpm. What is the increase in head developed by the pump if speed increase to 1000rpm? ANSWER: 78.76 m
Water flows through an orifice at the vertical side of a closed cylindrical tank. The water level inside the tank remains constant at 3m and the pressure at the top of the tank is 30KPa. If the jet strikes the ground horizontally by 4.5m and below the vena contracta by 1m, determine the coefficient of velocity.
A pipe has an initial radius of r1, which then changes to a radius of r2. The velocity of the water in the initial part of the pipe is v1. The segment of the pipe with the smaller radius is also 0.5 m higher than the initial pipe segment. What is the pressure difference between the two parts of the pipe? let r1=10cm let r2=6cm let v1=5m/s b) What is the volume flow rate in the pipe?
The water is flowing through a pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 35 litres/s. The section 1 is 6 m above datum and section 2 is 4 m above datum. If the pressure at section 1 is 39.24 N/cm2, find the intensity of pressure at section 2. Sketch the arrangement.
2.4) A pipe discharges 142 lps of water into a reservoir at a point 1.85 m below the water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25 m above the water surface. At the discharge end the pipe is 30.5 cm. If the head loss from A to the reservoir is 0.7 m, determine the pressure in A.
A water turbine operating at 85% efficiency is under a head of 100 m. If the constant discharge is 1000 gallon/sec, evaluate the operating speed of the turbine.
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST
A pump is designed to fill a pressurized tank rated at 1 MPa anda height of 23 m. Determine the power requirement of the pump inkW if the flowrate is measured at 20 m3/min.