6.3 For a water flow in a pipe, determine the pressure gradient required to accelerate the water at 20 fus for (a) a horizontal pipe, (b) a vertical pipe with the water flowing upward, and (c) a vertical pipe with the water flowing downward. Explain why the pressure walians diffang inpwargntnen case thì and case (c).

6.3 For a water flow in a pipe, determine the pressure gradient required to accelerate the water at 20 fus for (a) a horizontal pipe, (b) a vertical pipe with the water flowing upward, and (c) a vertical pipe with the water flowing downward. Explain why the pressure walians diffang inpwargntnen case thì and case (c).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pump in Fig. draws gasoline at 20 ° C from areservoir. Pumps are in big trouble if the liquid vaporizes(cavitates) before it enters the pump. ( a ) Neglecting lossesand assuming a fl ow rate of 65 gal/min, fi nd the limitationson ( x , y , z ) for avoiding cavitation. ( b ) If pipe frictionlosses are included, what additional limitations might beimportant?
Answer seems to be 736kpa, please show Formula and calculation as fast as (handwritten only) A 75-m-high water body that is open to the atmosphere is available. Water is run through a turbine at a rate of 200 L/s at the bottom of the water body. The pressure difference across the turbine is
sollve both, show both solutions and steps for both problems
If a pump discharges 284 liters per minute of water whose density is 985 kg/m3; find a) the mass flow rate in kg/min, and b) the total time required to fill a vertical cylindrical tank 3.05m in diameter and 3.05m high.
A water pump dissipates power on the shaft N=5.5 kW. Refine parameters: Head, flow and efficiency of the pump. Knowing the residual pressure Pair = 20, open the pump outlet (head) and the vacuum pressure at the inlet Pa,= 4m (head). The velocity in the thrust tube v2=4 m/s, the ejector tube diameter 75 mm, the suction pipe diameter 100 mm and the difference between the vacuum gauge and the manometer zero. Kinetic correction factor, geometry (Z2) -Z0). Ignore the height POST
For the system shown below, calculate (a) the volume flow rate of water from the nozzle and (b) the pressure at point answer should be a. 58.1 Kpa b. 0.0213 m^3 / s
As shown in the figure, the water is directed downward in the installation with a 25 ° angle narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Where the flow is frictionless and gravitational effects are neglected, a) Find the effective pressure at point 2. b) Calculate the x and y components of the force needed to hold the elbow in place and the resultant force. (psu =1000 kg/m3, g = 9.81 m/s2).
As shown in the figure, the water is directed downward in the installation with a 25 ° angle narrowing elbow in a piping system with a volumetric flow of 0.025 m3 / s. Effective pressure at 1 point is measured as 2 bar. Where the flow is frictionless and gravitational effects are neglected, a) Find the effective pressure at point 2. b) Calculate the x and y components of the force needed to hold the elbow in place and the resultant force. (pwater =1000 kg/m3, g = 9.81 m/s2).
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Suppose that you are willing to determine the diameter of the water jet impinging to the sink from the kitchen tap.The tap is produced to supply three different flow rates of the low, medium, and high. For each flow rate level, waterthat comes from the tap fills the beaker with a volume of 30 mL in 10 s, 6 s, and 2 s, respectively. The outlet of the tapis 13 mm, and the distance between the tap outlet and the sink is 53 mm. Determine the diameters of the water jetimpinging on the sink at three given flow rates.
A water truck drives slowly around a construction site, spraying water to keep dust down. A pump maintains a constant pressure of 100 kPa, gage, and the water is dispersed through 20 spray nozzles, each of diameter 0.01 m. If the truck is initially filled with 4000 L of water, and the flow rate is constant, determine how long the truck can drive before a refill is necessary in seconds.
(a) the total dynamic head (TDH) in meters (b) the water power (WP) in kW (c) the pump mechanical efficiency (%) if the power input to the pump is 15hp