For the wye fitting below, which lies in a horizontal plane, the cross-sectional areas at sections 1, 2 and 3 are 1 ft2 , 1 ft2 and 0.25 ft2 , respectively. At these same respective sections the gage pressures are 1000 lb/ft2 , 900 lb/ft2 and 0, and the flow rates are as shown below in ft3/s or cfs. What x and y force components would have to be applied to hold the wye in place?

Q: 5. Kerosene (sp.gr. = 0.88 ) enters the cylindrical arrangement as shown on the figure at section 1…

A: Given data: Calculate the density of kerosene as follows:

Q: Oil (SG = 0.89) enters at section 1 in Fig. P3.20 at a weight flow of 250 N/h to lubricate a thrust…

A: Given data: Specific gravity of oil, SG = 0.89 Weight flow rate, W = 250 N/h The mass flow rate of…

Q: Air at 15°C flows through a large duct and thence through a 75-mm-diameter hole in the thin metal…

A: Given:- T=15°C  C=0.62 d=75mm=0.075m ∆hw=31.7mm=0.0317mρw=1000 kg/m3ρair=1.225 kg/m3 at 15°C To…

Q: Note: This page should be the first page of vour report Q1) Water flows from a large tank through a…

A:

Q: For each flow speed setting calculate the air volumetric flow rate, Q, using the Venturi manometer.…

A: Given DataD=108.1mm=108.1×10-3md=29.6mm=29.6×10-3m△P=32.1-26.8=5.3kPaCd=0.98taken

Q: Air at standard atmospheric condition flows through a pipe at a velocity of 20 m/s, which then…

A: Ans: 995 Pa

Q: Question 4: Calculate the velocity in the pipe shown below, which connects minor headlosses 20 m

A:

Q: Problem 5: Water at 20°C flows steadily at 40 kg/s through the nozzle in the following figure. If D1…

A: A nozzle is a device that is used to regulate the direction or properties of a fluid flow as it…

Q: Water flows through the pipe system as shown, mass flowrate A divides equally into B and C, and…

A:

Q: A fabricated assembly made from three different sizes of standard steel tubing is shown below. The…

A: Given dataIncoming Flow rate of water = 0.072 m3/sThere are two branchesBranch 1  has a velocity of…

Q: Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h₁ =…

A:

Q: In Fig. X6.5.3, both nozzles discharge water horizontally into the atmosphere at 30 fps. Find 0 so…

A: Given Data The velocity of water in the pipe, V1=V2=V3=30 ft/s For pipe 2 Flow rate Q2=A2V2

Q: 6. A pump is located 4.5 m to one side of, and 3.5 m above a reservoir. The pump is designed for a…

A: kinematic viscosity of water at 5 °C is, v=1.519×10-6 m2/sec,Reynolds number,…

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A:

Q: Water of density 1000 kg/ m³ and kinematic viscosity 1.022 X 106 m²/s, is pumped between two…

A:

Q: Find the flow rate that occurs in m3/h. Take π = 22/7.  Determine the Reynolds number of this flow.…

A:

Q: Nozzle of diameter 20 mm is fitted to a pipe of diameter 10 min find the force exerted on the water…

A: Given:d=20 mmD=10 mV1=1.2 m/min

Q: Find the diameter of a pipe of length 6 km when rate of flow of water through the pipe is 250…

A: Find the diameter of pipe using chezy's formula.

Q: 10. Two galvanized iron pipes of diameter D are connected to a large water reservoir as shown. Pipe…

A:

Q: Q6:The block shown in fig.(3) weighs 5N and is held up by the water jet issuing from the nozzle.…

A:

Q: A centrifugal pump is used to pump a liquid in steady turbulent flow through a smooth pipe from one…

A:

Q: In car service station water flows through a vertical pipe reduced from a pipe of diameter D to…

A: The schematic diagram of pipe is as follows:

Q: Problem 3. Performance data for a pump are given in the table below. From a curve fit to the data,…

A: "Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: If the velocity of flow in a 75 mm diameter fire hose is 0.5 m/s, what is the velocity in a 25 mm…

A: Let us consider, Fire hose = Section 1 Jet = Section 2   Given, Diameter of section 1 = D1 = 75 mm =…

Q: A horizontal pipe of (40cm) dia. expanded suddenly to (60cm) dia. with a flow rate of water equals…

A: Given data: - The initial diameter of the pipe is d1 = 40 cm. The final diameter of the pipe is d2…

Q: For the flow configuration shown, you are required to design a pump station to transfer water from…

A: For designing of any pump station, various types of losses are considered. Losses such as major…

Q: A commercial venturi meter is placed in a vertical pipe as shown below. Pressure gauges are located…

A: To find : Calculate downward discharge of of water and also calculate velocity at the section 2…

Q: A fluid is flowing in a horizontal pipe 8 in. in diameter with a mean velocity of 10 ft/s. The…

A: (a) Specific weight of water is The total heat can be determined as,

Q: A horizontal water pipe is reduced in size from 18 inches in diameter from point A to 6 inches in…

A: Diameter at A, DA=18 in=1812ft=1.5 ftDiameter at B, DB=6 in=612ft=0.5 ftWater flow rate, Q=10…

Q: Oil is flowing at the rate of 3.14 cfs in a pipe of varying cross section. At section A, the…

A: Given data: Oil flow rate = 3.14 cfsSection A diameter = 6 inch = 0.5 ftPressure at A  = 12 Psi = 12…

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A:

Q: 1. A siphon has an uniform circular section of 70 mm diameter and consists of a bent pipe with its…

A: for answers apply bernollis equation between A and C for Vc and for Pressure at B apply between A…

Q: 2. The diameter of a pipe at the larger end is 0.5 cm and at the smaller end is 0.2 cm, the larger…

A: Data given-  PA = 5200 kN/m2  VA = 1.2 m/s  DA = 0.5 cm  DB = 0.2 cm  ZA = 7 m  ZB = 3 m

Q: A pipe transports 1962 N/s of water. The pipe tees into a 2"-diameter pipe and a 3"-diameter pipe.…

A:

Q: Water under a gauge pressure of 350 kPa flows with a velocity of 5m/s through a right- angle bend…

A: As per given question  Inlet pressure =350kpa Inlet velocity =5m/s Right angle bend=250mm We have to…

Q: Water in a main pipe at street level is at a gauge pressure of 140 kPa and is moving with negligible…

A:

Q: A pipeline of 50 mm diameter and 4.5 km length connects two reservoirs whose constant difference of…

A:

Q: The dimensions of a duct system, supplying air at 20°C to two zones 5 and 6 are shown in Fig. The…

A:

Q: Need asap A horizontal pipe of cross section 1.5 in2 has a constriction of cross section of 2 cm2 .…

A: Given data,  Horizontal pipe area a1=1.5 in2  Or a1= (1.5/144) ft2 Constriction area a2 = 2 cm2  Or…

Q: A horizontal 90° elbow connects two 300 mm diameter pipes. The rate of water flow is 180L/s. The…

A:

Q: Problem 4: For the siphon in the figure below, calculate (a) the volume flow rate of water through…

A:

Q: 6. A fabricated assembly made from three different sizes of standard steel tubing is shown below.…

A: The equation based on the principle of conservation of mass is called the continuity equation. thus…

Q: A piezometer and a Pitot tube are tapped into a horizontal water pipe, as shown in the Figure I…

A: SolutionLets take point(1) and (2) along the centerfine of the pipe with point(1) is directlyunder…

Q: A pipe with a radius of 7.5 mm is attached to a garden hose with a nozzle, If the velocity of flow…

A: Use continuity principal to solve this problem, Find Q and V2

Q: A fire pump delivers water through a 150 mm main to a hydrant to which is connected a 75 mm hose,…

A: At 1 to 3 , apply bernoulli's equationP1ϑ+v122g+z1=P3ϑ+v322g+z3+HL  ,equation 1A1v1=A3v3  ,…

Q: Air flows thru a device shown in the figure below. If the flow rate is large enough, the pressure…

A:

Q: A reservoir supplies water as shown in Fig. 1. The pipe system consists of 6 m of pipe and two 90°…

A: In the given system hydrostatic head of the reservoir is converted into a velocity head in the pipe.…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.