Answered: (7) For the state of plane stress shown…

(7) For the state of plane stress shown in the figure, determine the normal and shear stresses acting on the inclined plane of AB. 10 MPa A 30 50 MPa X

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Related questions

Q: For the state of stress given in the Figure below determine the following: 1. the principal stresses…

A: Given:σx=18 MPaσy=-14 MPaζxy=12 MPa

Q: Determine the plane stress state shown in the figure below. a) The main plans; b) The main stresses;…

Q: At a point in a stressed body, the cartesian components of stress are Oxx = 60 MPa, Guy = -40 MPa,…

A: Given Data σxx=60 Mpa σyy=-40 Mpa σzz=20 Mpa τxy=-40 MPa τyz=20 MPa τxz=30 MPa Stress tensor,…

Q: A roadway sign that weighs Py = 11 kN is supported by a structural pipe with an outside diameter of…

Q: Draw the Mohr's Circle of the stress element shown in figure. Find:- 6 MРа A 6 MPa The stresses…

Q: For the state of stress given below, a) Determine principal stresses and principal planes b)…

Q: At a point on the free surface of a stressed body, the normal stresses are 20 ksi (T) on a vertical…

Q: Question 2) Forces of F1 =8 kN in the z direction from the point B in the figure, F 2 =6 kN in the z…

Q: For the state of plane stress shown in Figure-1. t a) Draw Mohr's circle, b) Determine the maximum…

A: Given data:- σx=-20MPa,σy=90MPa,τxy=60MPa Center of mohr's circle=σx+σy2,0=-20+902,0=(35,0) Radius…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S = 75 MPa and Sy =…

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: Q2: A șteel pipe with an outside diameter of (95 mm) and an inside diameter of (85 mm) supports the…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 3700 psi, Sy =…

A: Find angle with vertical to find the normal and shear stress at the given plane, θ= 90 - β= 90-49=…

Q: H.W: A steel pipe with an outside diameter of 4.500 in. and an inside diameter of 4.026 in. supports…

Q: Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and…

A: Given:σx=60 MPaσy=-18 MPaζxy=15 MPa

Q: If the principal stresses in a plane stress problem are ơ1 = 100 MPa, ơ2 = 40 MPa, the magnitude of…

A: Write the given values along with suitable variables.

Q: 50 MPa 90 MPa 35 MPа 60 90 MPa 50 MPa 30

Q: if the maximum and minimum principal stresses at a point are (27 Mpa) and (5 Mpa) respectively. The…

A: Maximum shear stress is equal to difference of maximum principal stress and minimum principal stress…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Given: σx=62 MPaσy=-85 MPaτxy=56 MPa Solution: Sign convention: The tensile stress is positive The…

Q: - The state of plane stress at a point is shown on the element in Figure below. Represent this state…

Q: Determine the following using the formula & Mohr Circle a) Principal stresses b) Normal and Shearing…

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: For the assembly shown in the figure below, Determine the state of stress at point A on the cross…

Q: rect stresses of 160N/mm tensile and 120 N/mm compressive exist on two perpendicular planes at a…

A: Given, direct tensile stress, σt=160N/mm2 Compressive stress, σc=120N/mm2 The greatest principal…

Q: Q1) A stat of stress is specified in Figure. By using Mohr's circle determine the normal and…

A: Given:σx=60 MPaσy=-18 MPaζxy=15 MPa

Q: Q2: For the stresses at the point shown, find: The maximum shearing stress. • The principal stresses…

A: To Find : the maximum shearing stress the principal stresses and planes Given : stress acting…

Q: The stresses acting on element A in the web of a train rail are found to be ‘X (MPa)’ tension in the…

A: Given data:-σx=75MPa, σy=-90MPa(-ve for compression) and τxy=40MPa⇒Center of Mohr's…

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b)…

Q: The figure depicts the state of plane stress at a point. Sketch Mohr's circle for stress. Indicate…

Q: Q1 / If the cross section of the femur can be approximated as a circular tube, determine the state…

A: The free-body diagram of the problem can be sketched as follows, Let the upward normal force at the…

Q: Determine the absolute maximum shear stress of the stress state acting on the element shown in the…

A: It is required to determine absolute maximum shear stress

Q: In the figure shown, determine the normal stresses at AD • , shearing stress at + and BC bolt D • ,…

A: Solution: The free body diagram of the EDC is shown above, we need to find the reactions RD and RC…

Q: The state of plane stress at a point is represented on the element shown in the figure below. (a)…

A: Given details: σx=16 MPa, σy=0, ζxy=-10MPa Formula for principal stress: σ12=σx+σy2±σx-σy22+ζxy2…

Q: At a point in a stressed body, the known stresses are o, = 15 ksi (T). o, 12 ksi (T). oz = 11 ksi…

A: Given Dataσx=15ksiσy=12ksiσz=11ksiτxy=3ksiτyz=-4ksiτzx=0θ1=41°θ2=61°θ3=63.77°

Q: · Three forces are applied to the structure shown in Figure 3. Determine the maximum possible normal…

A: Given: Fy=-0.5 kNFx=-3 kNFz=-2.5 kN

Q: Q4- Draw Mohr's circle for the case as seen in Fig. 4. Determine the principal stresses and the…

A: According to the given information we have stress in x-direction and stress in the y-direction and…

Q: Listed below is a combination of stresses acting at a point and referred to axes x and y in an…

A: As Given in case (1); σx= -60 N/mm2 , σy= -36 N/mm2 , ζxy= 5 N/mm2 So the principal stresses will be…

Q: The state of plane stress at a point on the surface of the airplane fuselage is represented by the…

A: To find- 1. The maximum principal stresses and the maximum in plane shear specifying the…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: At a point on the flat surface of a member, load-stress relations give the following stress…

A: GIVEN: σxx=100 MPaσyy=0σzz=100 MPa τxy=20 MPaτxz=0τyz=20 MPa To find the principle stress σ2 and its…

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: 2.6. The principal stresses at a given point are ơ1 =10 ksi, o2 =5 ksi. Sketch Mohr's circle for…

A: givenσ1=10ksiσ2=5ksi

Q: 1) For the state of stress shown in figure, use the Mohr's circle method to determine (a) The…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are 5x = 95 MPa and Sy=…

Q: Determine the normal and shear stresses at point D that act perpendicular and parallel,…

A: Given: The load at the point D is 10 kN. The beam is shown below:

Q: Calculate the principal stresses and angles and in-plane maximum shear stresses and angles for t…

A: Given Data⇒ σx=20 MPaσy=30 MPaζxy=60 MPa

Q: A certain point in the mechanical part has shearing and normal stresses measured in MN/m^2 as shown…

A: In Mohr's circle we take a suitable scale to construct the circle. Accordingly we draw the circle.

Q: The stresses shown in the figure act at a point in a stressed body. If o = 115 MPa in the direction…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

100%

(7) For the state of plane stress shown in the figure, determine the normal and shear stresses acting on the
inclined plane of AB.
10 MPa
A
309
50 MPа
Y
X

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1 A rectangular steel plate with thickness t = 5/8 in. is subjected to uniform normal stresses a and ., as shown in the figure. Strain gages A and B. oriented in the x and v directions. respectively, arc attached to the plate. The gage readings give normal strains = 0.00065 (elongation) and £. = 0.00040 (elongation). Knowing that E = 30 X 106 psi and v = 0.3, determine the stresses c7 and a, and the change .11 in the thickness of the plate.
An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the xy axes, that is, determine crv, tr(_, and t. Show the results on a sketch of an clement oriented at B = 10
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Solve the preceding problem if the norm al and shear stresses acting on the element are sx = 2100 kPa, sy= 300 kPa, and txy= -560 kPa, and the seam is oriented at an angle of 22.5° to the clement.
-27 A square plate with side dimension of 2 in. is subjected to compressive stress a and tensile stress The stresses on element A oriented at angle ?? x1=45° aresy1= 75 psi. tx1y1= 275 psi. . Find the state of stress on the element lilt is rotated clockwise to align the x3 axis with the horizontal x axis.
A state of stress is specified in the figure shown below. Determine the Normal stress σx (mPa) on the Principal Plane if Px = -60 mPa; Py = -84 mPa and v = 55 mPa
A cylindrical storage tank contains liquefied propane under a pressure of 1.5 MPa (gage pressure P=1.5 MPa) and is subjected to an axial force F=60 kN. Knowing that the tank has an inner diameter of 320 mm and a wall thickness of 3 mm, find the principal stresses and determine the maximum shear stress.
Draw Mohr’s circle for sx = sy = txy = 2 kPa. On the circle, label the axes and the principal stresses and their angles. Using three significant digits, determine the principal stresses and their angles, and the normal and shear stresses at q = 80 degree. The three gages from the strain rosette mounted on a steel shaft have the following readings: εa = 0.000316, εb = 0.000248, and εc = 0.000579. Determine the strain components: εx, εy, and Yxy.
A 60˚ strain rosette measures the following strain at a point on the aluminum skin ofan airplane. ϵ0 = 160 ×10-6 m/m, ϵ60 = -220 ×10-6 m/m and ϵ120 = 360 ×10-6 m/m. Using E = 10 ×106 psi and v = 0.3, Determine the principle stresses and the maximum in-plane shear stress.
Considering the original state of stress as shown in figure below and recalling the already developed equations for normal and shear stress at an angle Ɵ c.c.w from x-axis, mathematically prove that the planes of maximum in-plane shear stress are inclined at 45o to the principal planes.