Q2: A șteel pipe with an outside diameter of (95 mm) and an inside diameter of (85 mm) supports the loadings shown in Figure. Determine the normal and shear stresses on the surface of the pipe at point H. 450 mm A 2R

Q2: A șteel pipe with an outside diameter of (95 mm) and an inside diameter of (85 mm) supports the loadings shown in Figure. Determine the normal and shear stresses on the surface of the pipe at point H. 450 mm A 2R

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.16P: A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm....

See similar textbooks

Related questions

Q: F 30° ød. 2 M. 10

Q: For the state of stress given in the Figure below determine the following: 1. the principal stresses…

A: Given:σx=18 MPaσy=-14 MPaζxy=12 MPa

Q: Determine the plane stress state shown in the figure below. a) The main plans; b) The main stresses;…

Q: A roadway sign weighs 5.4 kN and is supported by a structural pipe that has an outside diameter of…

Q: 1- The normal and shearing stresses at point K 2- Sketch the results on a differential volume…

Q: A certain point in the mechanical part has shearing and normal stresses measured in MN/m^2 as shown…

A: Write the given data.

Q: For the state of plane stress shown in Figure-1. t a) Draw Mohr's circle, b) Determine the maximum…

A: Given data:- σx=-20MPa,σy=90MPa,τxy=60MPa Center of mohr's circle=σx+σy2,0=-20+902,0=(35,0) Radius…

Q: The state of stress at a point in the machine element is shown in figure below. Determine the normal…

Q: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

A: Note: Since you have posted a question with multiple sub-parts, we will solve the first three…

Q: The forces applied to the pulleys are given in the figure below. Accordingly, show the stress…

A: Given: The outer diameter of shaft, D = 25 mm The inner diameter of shaft, d = 20 mm

Q: In the figure below, a crane is supported by two cables of cross-sectional area equal to 3.04 cm2.…

Q: If the principal stresses in a plane stress problem are ơ1 = 100 MPa, ơ2 = 40 MPa, the magnitude of…

A: Write the given values along with suitable variables.

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: 90 MPA 60 MPA 20 MPA

A: Given that, σx=-20 MPa,σy=90 MPa,τxy=60 MPa, Steps to draw mohr's circle: 1. Take direct stress at…

Q: Q - The mechanism of bone as a solid rod shown in figure. The diameter is 4 cm and it is subjected…

A: Acting torque on the system = 200 ×0.15 =30 Nm Bending moment at end section = 200 ×0.25 = 50 Nm the…

Q: Ql: For the Figure shown below, determine (a) the principal stresses and show them on a sketch of a…

Q: Q2 Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is A mm, and…

Q: Q1: A certain point in the mechanical part shown in Figure below. Use Mol determine: (a) the…

A: Givenσx=60 MN/m2=60MPaσy=-50MN/m2=-50MPaτxy=30MN/m2=30MPa

Q: 1- Find the shear stresses at A and B points when the force V applied to the beam is 20 kN. 200 mm…

A: Given, The width of the I-section, b=125 mm The height of the I-section, h=250+30+30=310 mm The…

Q: Problem 1-5 The Cartesian components of stress at a point are given below : Oy = 5, Tyz = - 4,…

Q: The stress at a certain point is as shown in the figure. If the maximum in-plane shear stress…

Q: If the principal stresses in a plane stress problem, are o1 = 100 MPa, o2 = 40 MPa, the magnitude of…

Q: stress, is shown in the figure below. If the minimum stress, is shown in the figure below. If the…

A: Given: The state of stress at a point,σx=100 kPaτxy=50 kPaσ2=10 kPa(minimum principal stress)

Q: Q2: A rigid platform weighing 53.5 kN is supported by three equally spaced rods. The arrangement is…

Q: A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank…

A: Given data: do=180 mmt=13 mmP=15.1 MPa Need to determine the longitudinal and hoop stresses in the…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Need to determine normal stress σn or ( σx ) In the given answer normal stress is shown by σn Data…

Q: The state of plane stress at a point is shown on the element in Figure below. Represent this state…

A: Given: The orientation of element, θ = 45° The stress along x-axis, σx = -10 ksi The stress along…

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: 5. The normal and shear stresses acting on one plane passing through a point in a soil mass are 120…

Q: 1: The inner and outer diameters of the pipe is 50 mm and 75 mm, respectively and it is made of cast…

A: The normal stresses will be acting due the normal forces as well as bending moments on the rod. The…

Q: Q.1) For the given state of stress at a point (Normal stresses are 200 & 150 MPa, and Shear stress…

A: Given data:6x=-200MPa6y=-150MPa → compressive normal stressτxy=100MPaθ=30°To find:1) Normal…

Q: (7) For the state of plane stress shown in the figure, determine the normal and shear stresses…

A: Given data: The stress in the x-direction is σx=-50 MPa The stress in the y-direction is σy=0 MPa…

Q: The stresses shown in the figure act at a point in a stressed body. If o = 239 MPa in the direction…

Q: When there is a plane stress condition as shown in the figure, display this stress in the form of…

Q: 1. Calculate the maximum stresses to occur in the hole and groove (groove) areas in the plate below,…

A: Given, Applied load (F)=5000N Width of the plate=200mm The thickness of the plate (t)= 25mm Diameter…

Q: 1) There is a cylindrical rod mounted on the auxiliary machinery. The loadings are shown in the…

Q: 2- The state of plane stress at a point with respect to the xy-axes is shown in Fig, find the normal…

A: To find : The normal and shear stress on section inclined at an angle of 30° Given : The stress in…

Q: Internal pressure and axial tensile force are applied to an open cylindrical tank 605 mm in diameter…

Q: The state of stress at a point, for a body in place stress, is shown in the figure below. If the…

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A: Loads acting on a body induces stresses in all directions at any point of the body. The point can be…

Q: The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi…

A: Among the applied normal stresses on mutually perpendicular planes the stress corresponding to…

Q: Q#4: Considering the original state of stress as shown in figure below and recalling the already…

A: The equation for the normal stress at an angle θ from the x-axis is given by,…

Q: For the state of plane stress, stress components are shown on the element in Figure Question 1: a)…

Q: 10 MPa 9. Using Mohr's circle, for the figure at the right, determine: a) The angle to the principal…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: qo M h For the given system; a) Draw internal force diagrams and determine the most critical…

A: Consider horizontally forward & vertically upward force as (+)ve and horizontally backward &…

Q: Q2) Look at the Mohr Circle and find (the scale is 1 cm-10 MPa) 1. Normal and shear stress at points…

A: Since we only solve upto three subparts at a time, we will solve the first three. Please specify the…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

Q: A certain point in the mechanical part has shearing and normal stresses measured in MN/m^2 as shown…

A: In Mohr's circle we take a suitable scale to construct the circle. Accordingly we draw the circle.

Q: F2. F3 F1 L2 A pipe is subjected to loads as shown in figure. The outer and inner diameters of the…

A: Given: The inner diameter of pipe, d = 79 mm The outer diameter of pipe, D = 99.2 mm The force along…

Q: In the case of the infinitesimal elements shown in the figures, determine the normal and shear…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Q2: A șteel pipe with an outside diameter of (95 mm) and an inside diameter of (85 mm) supports
the loadings shown in Figure. Determine the normal and shear stresses on the surface of the pipe
at point H.
450 mm
A 2rRt
1- J/2 = Rt
10 kN
R
7 kN
14 kN
240 mm
Ray
2R
(2/)Rav

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.
The shear stresses t in a rectangular beam arc given by Eq. (5-43): in which Fis the shear force, / is the moment of inertia of the cross-sectional area, /lis the height of the beam, and i] is the distance from the neutral axis to the point where the shear stress is being determined (Fig. 5-32). By integrating over the cross-sectional area, show that the resultant of the shear stresses is equal to the shear force V.
A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown in the figure.If the vessel sustains an internal pressure of 450 kPa, determine the average shear stress in theglue and the state of stress (axial and hoop components of stress) in the wall of the vessel.
Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 N - m . Determine the average shear stress developed at point A. The tube is fixed at the other end. a) 1.75 MPa b) -1.65 MPa c) 4.086 MPa d) 2.095 MPa If your doing it fast, I will rate you...
The tank shown in the figure is fabricated from 10 mm steel plate. Determine themaximum longitudinal and circumferential stress caused by an internal pressure of 1.2MPa.
Q2. A mild steel shaft transmits ‘P’ kW at ‘N’ r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa. Power P in KW= 25 , Speed N in rpm=150
Consider a tube having a rectangular cross-section as shown below. The tube is subject to two twisting moments of 70 N - m . Determine the average shear stress developed at point A. The tube is fixed at the other end. a) 1.75 MPa b) -1.65 MPa c) 4.086 MPa d) 2.095 MPa
Determine the maximum and minimum hoop stresses across thesection of a pipe of 400mm internal diameter and 100mm thick when a fluid undera pressure of 8N/mm2 is admitted. Sketch also the radial pressure and hoop stressdistribution across the thickness.
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.40 ksi. Determine the absolute maximum shear stress on the inner surface of the cylinder wall.