7. The size of the supply-side bonding jumpers for each of the individual raceways in the parallel set is required to be based on the size of the largest _______ conductor in each raceway or cable. A. equipment grounding B. electrode grounding C. ungrounded service-entrance D. neutral

7. The size of the supply-side bonding jumpers for each of the individual raceways in the parallel set is required to be based on the size of the largest _______ conductor in each raceway or cable. A. equipment grounding B. electrode grounding C. ungrounded service-entrance D. neutral

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter11: Lighting Branch Circuit—front Entry, Porch,post Light, Underground Wiring

Section: Chapter Questions

Problem 1R: How many circuit wires enter the entry ceiling box? How many equipment grounding conductors enter...

See similar textbooks

Related questions

Q: What is the minimum-size supply-side bonding jumper required if installed on the line side of a…

A: The supply-side bonding jumper is installed on the line side of a 300-ampere service disconnecting…

Q: In the conduit layout shown in picture attached, determine how many wires are contained in each…

A: The circuit is shown below: Between the three-phase line and the disconnect switch. The switch is…

Q: If a 1 1/4-in. EMT raceway containing three conductors is already filled to 20%, what is the…

A: Need to find cross sectional area of raceaway

Q: Describe what the following conductor designation means when it is printed on the insulation;…

Q: 17. In an air compressor system, the distribution piping can be bonded using the A. equipment…

A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Q: 11. What are at least two instances where a splice is allowed to be made in underground consumer's…

A: The power system has to transmit power from the generation side to the load side. For this purpose,…

Q: Identify and explain the safety procedures and precautions when working with tools and equipment's…

A: Electrical cables are used for transferring the signals and are also used for long distance…

Q: 2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service…

A: 2.a. Drip loops are used for preventing rainwater and moisture. Thus this is not a suitable…

Q: Which of the following statements about equipment grounding conductors is true? A. Unacceptable…

A: Correct option is B that is ELECTRIC GROUND CONDUCTORS must be capable of withstanding the higher…

Q: what section of the code prohibits supporting telephone wires from raceways that contain light or…

A: N.E.C. ARTICLE 820 article covers coaxial cable distribution of radio frequency signals or covers…

Q: n an ungrounded electrical systems with conductors installed in grounded metal raceways and…

A: In an ungrounded electrical system, there is no direct connection with the grounding electrode.…

Q: 12. What is the conduit and wire equivalent to a 400A bus duct with both copper and aluminum?…

A: The National Electrical Code (NEC) is a collection of rules for the secure electrical wiring wiring…

Q: The line described is 845 mi in length.The line contains four conductors, each weighing 2526 lb per…

A: since 1 mi = 5280 ft so 845 mi = 845×5280 = 4461600 ft so the length of the line =…

Q: what is grading of cables, explain proper in details with block diagram

A: In a single-core cable, the conductor is surrounded by the dielectric material with an outer…

Q: b) Differentiate between Insulated-Neutral and Earthed-Neutral systems as applied to electrical…

A: Question. b) Differentiate between Insulated-Neutral and Earthed-Neutral systems as applied to…

Q: A conductor with continuous white or gray covering shall be used only for the grounded circuit…

A: According to article NEC 200.6, the facts about the identification of the Grounded conductors are…

Q: How far can a 230V, 50A, three-phase load be located from a panelboard if it's fed with 3 AWG…

A: The Length of the load from the panel board is calculated as shown below

Q: What type of bonding jumper connects the grounded circuit conductor and the equipment grounding…

A: In a power system , Main bonding jumper connects the grounded circuit conductor and the equipment…

Q: mast-type service entrance

A: The service raceway according to NEC is defined as an enclosed channel specially designed to hold…

Q: How is the equipment grounding conductor sized?

A: The size of the equipment grounding conductor is determined using the data provided in the national…

Q: How many conductor volume allowances should be applied for the equipment grounding conductors in the…

A: We need to answer how many conductor volume allowances should be applied for the equipment grounding…

Q: 6. Which of the following is a condition that a liquidtight flexible metal conduit must meet in…

A: Given :few mcqs on flexible metal conduit

Q: 8. How do the terms ‘impedance drop’, ‘voltage drop’ and ‘voltage regulation’, in connection of…

A: Impedance drop: Impedance drop is the product of the current and the internal impedance. The…

Q: Q.12 What provides branch-circuit protection, and where is it located? Select one: A. BREAKERS…

A: 12. A fuse is an electrical gadget used to shield the circuit from overcurrent. It comprises a…

Q: In terminating the coaxial cable, If the present procedure is to loosen up the braided shield and…

A: In terminating the coaxial cable, the the flaring and bending back the outer braid onto the cable…

Q: Determine the Primary Conductor Size (include the AWG size number), Secondary Conductor Size…

A: P= 90 KVA Three phase transformer 400/230 V

Q: single-pole portable cable connectors for a portable switchboard on stage, where used, shall be…

A: single-pole portable cable connectors for a portable switchboard on stage, where used, shall be…

Q: Identify and describe the step-by-step process used to install cable in the any building?

A: Step by step process to install cable in any buildings: step 1: In the slab, a PVC conduit is laid…

Q: . A grounded circuit conductor and the equipment grounding conductor should always be joined at the…

A: Choose the correct option A grounded circuit conductor and the equipment grounding conductor should…

Q: procedures

A: Explanation: The safety procedures and precautions to be taken when working with tools and…

Q: The point of attatchment of the service drop conductors to a building must not be less than ______…

A: The point of attachment of the service drop conductors to a building must not be less than 10 feet.…

Q: List the minimum service drop clearances required by the NEC in the following residential…

A: The minimum service drop clearance required by the NEC (120 V/240 V) for the following residential…

Q: 19.a. Which term relates to the conductors connected to the output side of a separately derived…

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: In an ungrounded electrical systems with conductors installed in grounded metal raceways and…

A: In an ungrounded system, the system has no direct connection with the grounding electrode. When the…

Q: Which type of cable would you use to connect two buildings in an office installation? A. Buried…

A: Given & to find: Which type of cable would you use to connect two buildings in an office…

Q: Where insulated conductors are deflected within a wireway, either at the ends or where conduits,…

Q: A ____shall be used to connect the equipment grounding conductors, the service equipment enclosures,…

A: Given, 3 multiple choice questions related to national electrical code.(NEC). Please find the below…

Q: 14. If the total circular mil area of the largest ungrounded service-entrance conductor for a…

A: Explanation: The equivalent area of four ungrounded paralleled 500 kcmil conductors is 2000 kcmil.…

Q: What do you mean by permissible current loading of an underground cable?

A: Permissible current loading: It is the maximum amount of current the cable can carry without any…

Q: What is grading of cables, explain.

A: Grading is defined as the process of equalizing the stress in the dielectric of the cable.…

Q: A? Conductor is defined in NEC 240.2 as a conductor, other than a service conductor, having…

A: The article 240.2 determine the current limiting of the over current protective device is used to…

Q: What is the largest solid (not stranded) conductor approved for installation in raceways?

A: Solid conductor are made with a single conductive material while stranded conductor are made with…

Q: A two conductor street main AB, 500 meters in length is fed from both end at 250 volts. Load of 50A,…

A: The solution can be achieved as follows.

Q: The wording that I am running into with questions such as "The number of conductors required to be…

A: The number of conductors required to be installed between three-way and four-way switches is white…

Q: Is it advisable to use Multi-pair punch in terminating cables in patch panels? Why?

A: Patch panel: It is a local area network (LAN) that is a mounted equipment gathering that contains…

Q: The voltage drop percentage for a panel feeder with a no continuous load of 180A, using 3/0 THWN…

A: Given data, A 3/0 THWN copper conductors at 480 V Length, L=248' Load current, I=180 A

Concept explainers

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.

Question

7. The size of the supply-side bonding jumpers for each of the individual raceways in the parallel set is
required to be based on the size of the largest _______ conductor in each raceway or cable.
A. equipment grounding
B. electrode grounding
C. ungrounded service-entrance
D. neutral

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Compensation Techniques in Transmission Line

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In the conduit diagram shown in attached picture, determine how many wires are in each conduit between each piece of equipment. Identify each wire terminal connection and the quantity of wires, as shown in the example, above the disconnect
a. How many feet of 2-conductor bell wire cable are required? ______ b. How many feet of 3-conductor bell wire cable are required? ______
In the conduit layout shown in picture attached, determine how many wires are contained in each conduit between each piece of equipment. Identify each wire with a proper terminal marking, as shown in the example, above the disconnect switch.
Determine the minimum number of cubic inches required for two 10 AWG conductors passing through a box, four 14 AWG conductors spliced in the box, two 12 AWG conductors terminating to a receptacle, and one 12 AWG equipment bonding jumper from the receptacle to the box.
18. Which of the following would help avoid the choke effect in grounding electrode conductors?A. Installing a main bonding jumperB. Using an approved polyvinyl chloride conduitC. Applying solder to the connectionD. Using bonding bushes on the ends of the raceway
2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service head, andany fittings necessary for the termination and support of overhead service conductors?A. Drip loopB. Service lateralC. Service dropD. Service mast 2.b. What's likely to happen when connected parallel conductors are different lengths?A. An NEC violationB. Misidentification of conductor cablesC. An uneven distribution of currentD. Conductor termination
List the methods by which an equipment grounding conductor is connected to a device box.
When it comes to the installation and maintenance of cable systems, why is it so vital to follow a structured cabling standard?
Which of the following is a term missing from the National Electrical Code but used by manufacturers of equipment that's suitable for use as service equipment? Micro-grid  Selective coordination Neutral disconnect link Grounding triad The _______ is required to be connected to the grounded conductor of the sensitive electronic system on the line side of the separately derived system disconnecting means. main bonding jumper  equipment grounding terminal bus neutral ground strap neutral disconnect link
4. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
17. In an air compressor system, the distribution piping can be bonded using theA. equipment grounding conductor supplying the air compressor's motor.B. grounding electrode driven near the compressor motor.C. grounded neutral conductor.D. equipment grounding conductor at the service entrance. 18. Which of the following would help avoid the choke effect in grounding electrode conductors?A. Installing a main bonding jumper B. Using an approved polyvinyl chloride conduitC. Applying solder to the connection D. Using bonding bushes on the ends of the raceway
D.1-. Which of the following names is commonly used for armored cable on commercial and industrial jobsites?A. RomexB. BXC. ECGD. MCD.2. Which of the following is the most common type of conductor termination used in commercial andindustrial wiring applications?A. A pressure connectionB. A wire nutC. A wire spliceD. A crimped connection D.3. Which of the following terms correctly describes a ventilated metal enclosure that supports powerdistribution conductors of up to 8000 A and 69 kV, and that allows for proper phase arrangement of theconductors?A. A trolley busB. A channel racewayC. A cablebusD. A feeder bus