8. A Human arm model as shown is lifting a Weight W. Determine the stress developed In thebicep muscle of the model at point A if a welght of 150N is carried In the position shown. Takethe cross-sectional area at point A Is 600 mm2.BicepElbow -30 cm-Cm

Given data: The weight carries by the bicep at point A is WA=150 N The cross sectional area of the…

8. A Human arm model as shown is lifting a Weight W. Determine the stress developed In the bicep muscle of the model at point A if a welght of 15ON is carried in the position shown. Take the cross-sectional area at point A is 600 mm2.

8. A Human arm model as shown is lifting a Weight W. Determine the stress developed In the bicep muscle of the model at point A if a welght of 15ON is carried in the position shown. Take the cross-sectional area at point A is 600 mm2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A solid steel crank has an outside diameter of 32.95 mm. For the loadings shown, determine the…

Q: The clamp shown is made of members AB and AC, which are pin-connected at A. If it exerts a…

Q: Member BC shown is subjected to a vertical force of 45 kN. Determine the position S of this force so…

Q: A 120-mm diameter bolt is used in a clevis. Determine the shear stress on the bolt if a load of 350…

A: Given data, d= 120 mm F= 350 kN =350000 N

Q: The structure shown is made up of elements ABC, AD, BE, DF, joined by articulated connections at all…

Q: Steel wire AB and aluminum wire CA support the 400 kg mass as shown. Determine the required diameter…

Q: Determine the state of stress at point A of the rectangular post shown loaded with concentrated…

A: Ffgg

Q: The pressure tank shown has an 8-mm wall thickness and butt-welded seams forming an angle β=20° with…

A: Given Data: The pressure inside the tank is p = 600 kPa. The thickness of the tank is t = 8 mm. The…

Q: 4. A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37-5mm…

A: Find the value of force Q and stress at point C and D

Q: the pins at A and B if the allowable normal stress for member BC is Oallow = 35 ksi and the…

A: Handwritten.jpg

Q: Three wood boards, each 4 inches wide, are joined by the %-in-diameter bolt. Of the working stress…

A: Given Wood board wide= 4 in Bolt diameter = 3/4 in Maximum tensile stress = 800 psi Maximum bearing…

Q: A cast-iron machine part is acted upon by the 3 kN-m couple shown. Know-ing that E= 165 GPa and…

A: Given data Couple acting on the machine part, M = 3 kN-m. Draw the cross-section of the beam,…

Q: Q2 Design the rectangular key which is located on the shaft motor if the diameter of it is (48) mm…

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: The Bars of the Pin-connected frame as shown are each 30mm and 60mm in section. Determine the…

A: Given: σT=100 MPaσC=80 MPaSection=60 mm×30 mm The free-body diagram of the frame considering…

Q: Consider a 70 kg spiderman hanging at its web string as per the configuration shown. Determine the…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that dj =…

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: Given Data: Horizontal forces on pin is F = 5 kips +5 kips = 10 kips. The width of link AB and BC…

Q: 2. The frame shown carries a load P = 500 lb. If a = b = 10 inches, c = 18 inches, and s = 3/8 inch.…

Q: The forces P, and P, are applied to the post in the directions parallel to the x and y axes,…

A: Given: The length of post, L = 1000 mm = 1 m The diameter of post, D = 100 mm = 0.1 m The force…

Q: a force q of magnitude 3kips is applied to machine element ab. the uniform thickness of the element…

A: Given data Force (Q) = 3 Kips Thickness (t) = 0.8 in

Q: For the truss and loading shown, determine the magnitude of the normal stress(in psi) in member CE,…

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: force (iii) experiencing compression or tension. Determine the axial stress in all rods of the truss…

A: Given data: Distance between the supports (points G and A) = 4 m Need to determine the force in all…

Q: ! Required information Two horizontal 5.5-kip forces (P) are applied to pin B of the assembly shown.…

Q: The elevation of the platform is controlled by two identical mechanisms, only one of which is shown.…

A: Load = 1500 lb Here we need to draw free body diagram and solve the sum So here I am drawing it in…

Q: As shown below, two pneumatic cylinders are used to control the motion and displacement of the…

A: Given Applied load = 800 N Diameter of the control rods = 20 mm To find Normal stress of AE Normal…

Q: Two horizontal 12.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: Given: P = 12.39 kip d = 0.8 inch t = 0.5 inch

Q: For the riveted connection shown, the allowable shearing stress in the 25mm rivets is 140 MPa.…

Q: The four bars shown have the same cross-sectional area. For the given loadings, show that (a) the…

A: Givenpart aThe maximum compressive stresses are in the ratio4:5:7:9part bThe maximum tensile…

Q: a, determine stresses at an angle

A: Need to Determine the stresses

Q: Two horizontal 5.92-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: P = 5.92 kip d = 0.82 inch t = 0.5 inch

Q: A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three…

A: given data; ⇒a=1.2m⇒b=7.9m⇒c=2.9m⇒load(P)=40KN⇒load(Q)=75KN⇒area(A)=1120mm2⇒normal stress in each…

Q: A 240-kip load P is applied to the granite block shown. Determine the resulting maximum value of (a)…

A: a) Maximum normal stress can be determined as

Q: 2. Determine the smallest allowable cross-sectional areas of each 400 kN members for the truss…

Q: A 1600-lb-in. couple is applied to a wooden beam, of rectangular cross section 1.5 by 3.5 in., in a…

A: Given, Couple applied to the wooden beam of rectangular cross-section, M=1600 lb.in Width of the…

Q: Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 22 kN if it…

Q: Determine the maximum compressive stress in the bracket at section a–a when the load P = 52 kN is…

Q: The frame shown in Figure 5 consists of four wooden members, ABC, DEF, BE, and CF. Knowing that each…

A: Consider the free body diagram shown below for the given members ABC and DEF. Here,

Q: For the loading shown, determine (a) the stress at points A and B, (b) the point where the neutral…

A: Given data: Figure with loadings as shown To determine: Stress at A & B…

Q: A 150mm x 30mm x 250mm central wooden block is glued between cantilevered brackets 200mm x 50mm each…

A: Stress Stress is defined as the ratio of force to the area on which force is acting. There are…

Q: For the clevis connection shown, determine the shear stress in the 18-mm-diameter bolt for an…

Q: The two forces shown are applied to a rigid plate supported by a steel pipe of 8-in. outer diameter…

A: Draw the diagram of eccentricity of load.

Q: determine the maximum stress and the curvature of the bar.

Q: required thickness of member BC and the diameter of the pins at A and B if the allowable normal…

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

Q: 7.117 The pressure tank shown has a 8-mm wall thickness and butt welded seams forming an angle ß =…

Q: value of the shea nd the maximum ssive stresses. of each curve

Q: Two horizontal 6.79-kip forces are applied to pin 8 of the assembly shown. Knowing that a pin of…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

8. A Human arm model as shown is lifting a Weight W. Determine the stress developed In the
bicep muscle of the model at point A if a welght of 150N is carried In the position shown. Take
the cross-sectional area at point A Is 600 mm2.
Bicep
Elbow -
30 cm-
Cm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three forces, each of magnitude P = 3 kN, are applied to the structure shown. Determine the cross-sectional area of the uniform portion of rod BE for which the normal stress in that portion is +100 MPa. The cross-sectional area of the uniform portion of rod BE is mm2.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 29.13 lb. Express your answer in three decimal places.
Two solid cylindrical rods AB and BC are welded together at Band loaded as shown. Determine the magnitude of the force Pfor which the tensile stresses in rods AB and BC are equal. Take W= 12 kips. 30 in. -1.25 in. B W 25 in. 0.75 in. The magnitude of the force Pis kips.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P for which the tensile stress in rod AB is twice the magnitude as the compressive stress in rod BC.
A rod composed of an aluminum section rigidly attached between steel and bronze section. Axial loads are applied at the positions indicated. If P=3000 lb and the cross sectional area of the rod is 0.5 in 2, determine the stress in each section.
Two brass rods AB and BC, each of uniform diameter, will be brazed together at B to form a nonuniform rod of total length 100 m, which will be suspended from a support at A as shown. The density of brass is 8470 kg/m^3 Determine normal stresses of ((σzz)AB and (σzz)BC) as a function of z, and draw the variation of stresses with respect to z-axis on the same graph.
For the clevis connection shown, the shear stress in the 0.577-in.-diameter bolt must be limited to 22 ksi. Determine the maximum load P that may be applied to the connection.
The steel pipe AB has a 72-mm outer diameter and a 5-mm wall thickness. Knowing that the arm CDE is rigidly attached to the pipe, compute the length of the pipe, L, that causes the von Mises equivalent stress to be same at points H and K This IS NOT a graded assignment, it is supplementary study material.
The 1.4-kip load P is supported by two wooden members of uniform cross section that are joined by the simple glued scarf splice shown.Determine the normal and shearing stresses in the glued splice.
The Bars of the Pin-connected frame as shown are each 30mm and 60mm in section. Determine the maximum load P that can be applied without exceeding the allowable stresses of 100 MN/m2 in tension and 80 MN/m2 in compression.
Two forces P can be applied separately or at the same time to a plate that is welded to a solid circular bar of radius r. Determine the largest compressive stress in the circular bar (a) when both forces are applied, (b) when only one of the forces is applied.
A joint in a wooden structure shown has an applied loadF = 50 kN along the axis of the slanted member with anangle of 30°. Determine the shear stress developed alongthe plane CDE.Answer: τ = ___________________