14-8. Determine the required height h of the rollerpaster so that when it is essentially at rest at the crest ofne hill it will reach a speed of 100 km/h when it comes tone bottom. Also, what should be the minimum radius ofurvature p for the track at B so that the passengers do notxperience a normal force greater than 4 mg (39.24 m) N?leglect the size of the car and passenger.%3DA.Prob. 14-8

Given Data The maximum speed of the roller coaster is: v=100 km/h The normal force act on the…

--8. Determine the required height h of the rôller ster so that when it is essentially at rest at the crest of hill it will reach a speed of 100 km/h when it comes to bottom. Also, what should be the minimum radius of vature p for the track at B so that the passengers do not erience a normal force greater than 4 mg = (39.24 m) N? glect the size of the car and passenger.

--8. Determine the required height h of the rôller ster so that when it is essentially at rest at the crest of hill it will reach a speed of 100 km/h when it comes to bottom. Also, what should be the minimum radius of vature p for the track at B so that the passengers do not erience a normal force greater than 4 mg = (39.24 m) N? glect the size of the car and passenger.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

14-67. The assembly consists of two blocks A and B which have a mass of 20 kg and 30 kg, respectively. Determine the speed of each block when B descends 1.5 m. TI1c blocks are released from rest. Neglect the mass of the pulleys and cords
The roller coaster car has a mass of 700 kg, including its passenger. If it starts from the top of the hill A with a speed v A = 3 m/s, determine the minimum height h of the hill crest so that the car travels around the inside loops without leaving the track. Neglect friction, the mass of the wheels, and the size of the car. What is the normal reaction on the car when the car is at B1. find the Max g-force on passenger, bank angle2. the force required to slow down the motion and the time the force is applied must be determined to bring the coaster to rest.3. The maximum G-load experienced by a person should be no more than 5 g
17-35. The sports car has a mass of 1.5 Mg and a center of mass at G. Determine the shortest time it takes for it to reach a speed of 80 km/h, starting from rest, if the engine only drives the rear wheels, whereas the front wheels are free rolling. The coefficient of static friction between the wheels and the road is u, = 0.2. Neglect the mass of the wheels for the calculation. If driving power could be supplied to all four wheels, what would be the shortest time for the car to reach a speed of 80 km/h? G 0.35 m A -1.25 m-- -0.75 m
14-29 The train car has a mass of 10 Mg and is traveling at 5 m/s when it reaches A. If the rolling resistance is 1/100 of the weight of the car, determine the compression of each spring when the car is momentarily brought to rest
The roller coaster car has a mass of 700 kg, including its passenger. If it starts from the top of the hill A with a speed v A = 3 m/s, determine the minimum height h of the hill crest so that the car travels around the inside loops without leaving the track. Neglect friction, the mass of the wheels, and the size of the car. What is the normal reaction on the car when the car is at Bfind the Max g-force on passenger, bank anglethe force required to slow down the motion and the time the force is applied must be determined to bring the coaster to rest.The maximum G-load experienced by a person should be no more than 5 g and fint the bank angle
5. The 25-kg block AA is released from rest.
F14-1. The spring is placed between the wall and the 10-kg block. If the block is subjected to a force of F = 500 N, determine its velocity when s = 0.5 m. When s = 0, the block is at rest and the spring is uncompressed. The contact surface is smooth. S00N Prob. F14-1
The spring-held follower AB has a mass of 0.5 kg and moves back andforth as its end rolls on the contoured surface of the cam, where r = 0.15 m and z =(0.02 cos 2θ) m. If the cam is rotating at a constant rate of 30 rad/s, determine theforce component Fz at the end A of the follower when θ = 30°. The spring isuncompressed when θ = 90°. Neglect friction at the bearing C.
The smooth particle has a mass of 80 g. It is attached to an elastic cord extending from O to P and due to the slotted arm guide moves along the horizontal circular path r=(0.8sinθ)m. If the cord has a stiffness k= 24 N/m and an unstretched length of 0.25 m, determine the force of the guide on the particle when θ=60. The guide has a constant angular velocity θ˙=5rad/s
If the rod of negligible mass is subjected to a couple moment of M = (30t^2) N⋅⋅m, and the engine of the car supplies a traction force of F = (15t) N to the wheels, where t is in seconds, determine the speed of the car at the instant t = 12.5 s. The car starts from rest. The total weight of the car and rider is 1.5 kN. Neglect the size of the car.
The 5-kg collar has a velocity of 7 m/s to the right when it is at A. It then travels along the smooth guide. Determine its speed when its center reaches point B. The spring has an unstretched length of 150 mm and B is located just before the end of the curved portion of the rod
Each of the two elastic rubber bands of the slingshot has an unstretched length of 200 mm. If they are pulled back to the position shown and released from rest, determine the maximum height the 25-g pellet will reach if it is fired vertically upward. Neglect the mass of the rubber bands and the change in elevation of the pellet while it is constrained by the rubber bands. Each rubber band has a stiffness k = 50 N/m.