d) Venturi-type flowmeter shown in Figure 8 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, a is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. Calculate the volume flowrate of oil inside the conduit. 2(P,-P,) P(1– B*) Vventury AP oil D Figure 8

d) Venturi-type flowmeter shown in Figure 8 is used to obtain the flowrate of oil inside a conduit. The diameter of the venturi, a is one third of the pipe diameter, D. The pipe diameter D is 6 cm, pressure difference reading AP, is 25 kPa, discharge coefficient Ca, is 0.98, Bis the ratio of venturi diameter to pipe diameter and oil specific gravity, SG is 0.95. Calculate the volume flowrate of oil inside the conduit. 2(P,-P,) P(1– B*) Vventury AP oil D Figure 8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A2: FLUID FLOW, FLOW RATE & PRESSURE DROPProblem:3. Determine the volumetric flow rate, in L/s, for water flowing out of a faucet based on 6 L in 8 s.
The flow rate of a hydraulic fluid with a Sg of 1.08 through a 2-in. I.D. orifice is 50 gal/min. If the pressure drop across the orifice is 5 lbf/in.", what is the discharge coefficient?
What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the design velocity if the system is 3 m/s?
26. Inlet and throat diameters of a horizontal venturimeter are 270 mm and 130 mm respectively. The liquid flowing through the venturimeter is water. Pressure intensity at inlet is 19 N/cm2, while pressure at throat is 48 kPa. Find flow rate of water in lit/min, assuming Cd is 0.9 and also draw the neat sketch. i) Actual flow rate =
PROCESS INSTRUMENTATION AND CONTROL In a differential pressure flow meter, determine the velocity at the outlet for the given technical specification. The density of the liquid flowing through the pipeline is 997 kg/m³, Pressure at inlet is 10 lb/ft2, pressure at outlet is 8 lb/ft2 and cross sectional area of the orifice is 0.2512 m. Note: Ratio of meter diameter to pipe diameter is 0.5 and discharge coefficient is 0.61. Also, find the flow rate.
Water flows through a rubber hose 2 cm in diameter at a velocity of 4 m/s. (a) What must be the diameter of the nozzle in order that the water emerge at 16 m/s? (b) What is the rate of flow in cu.m per minute?
Gentlemen, please check and help me with question #3 Tank filled with water and orifice diameter of 3 cm in the bottom. Height between centre of orifice and water level 3 m. Coefficient of discharge - 0.64, coefficient of velocity- 0.97. Find: 1. Actual jet velocity? This one I know how to do. V(actual) = square root from 2gH 2. Jet diameter? This one I know as well. Coefficient of contraction= coefficient of discharge/ coefficient of velocity Diam of jet we will find from formula: Coefficient of contraction = (diameter of jet/diameter of orifice)^2 3. How long will it take for jet to be established?
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
You are the mechanical engineer supervising the layout of a piping system. In a certain portion of the pipe, the specifications are as follows: length of pipe is 10m, inside diameter of 30cm, outside diameter of 30.5cm, maximum allowable speed of 15m/s and a coefficient of 0.003456. If the uncertainties are 0.02mm for length, 0.8mm for the diameters and 0.1mm/s for the velocity, what loss of head will be imminent in this pipe?
You are the mechanical engineer supervising the layout of a piping system. In a certain portion of the pipe, the specifications are as follows: length of pipe is 10m, inside diameter of 30cm, outside diameter of 30.5cm, maximum allowable speed of 15m/s and a coefficient of 0.003456. If the uncertainties are 0.02mm for length, 0.8mm for the diameters and 0.1mm/s for the velocity, what loss of head will be imminent in this pipe? With all the above uncertainties, what is the total uncertainty in the head loss?
You are the mechanical engineer supervising the layout of a piping system. In a certain portion of the pipe, the specifications are as follows: length of pipe is 10m, inside diameter of 30cm, outside diameter of 30.5cm, maximum allowable speed of 15m/s and a coefficient of 0.003456. If the uncertainties are 0.02mm for length, 0.8mm for the diameters and 0.1mm/s for the velocity, what loss of head will be imminent in this pipe? In the piping system above, what is the uncertainty in computed head loss contributed by the velocity of the pipe?
A fountain and a water tank will be powered by water from a nearby lake. The elevations and pipe connections are depicted in the diagram below. The fountain's jet water should reach a height of at least 2.5 m from the nozzle outlet. The tank, on the other hand, is elevated to allow gravity to distribute water. The table below contains the specifications for nozzles, suction and discharge pipes. What is the minimum power input to the pump in kW, assuming negligible minor head losses? Assume that the pump efficiency is 88 percent and the motor efficiency is 95 percent. The fountain's water is returned to the lake via a drainage system.