Answered: 8. In the figure below a manometer uses…

8. In the figure below a manometer uses oil with specific gravity of 0.8. (a) Calculate the discharge when R = 1 ft. (b) Repeat the problem if the pipe is inclined at 30° upward.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The device shown in the figure is known as a venturi. In this specific venturi, the differential…

A: Given: The differential pressure between locations 1 and 2 is, P1-P2=5 psi. The diameter ratio is,…

Q: to pump water from lower reservoir to upper reservoir, a centrifugal pump is used. if the length of…

A: Given:Suction head=3 mdelivery head=30 m

Q: Water at 5°C is siphoned from a tank, as shown in the figure below. Depth of the lowermost parts of…

Q: Calculate the discharge through the pipe line shown in figure. Also find the pressure at point A and…

A: The density of water is 1000 kg/m3. The atmospheric pressure is 101325 Pa.

Q: Q/ The three water-filled tanks shown in figure are connected by pipes as indicated. If minor losses…

Q: À 2-in sch40 pipe line carries water at 70°C. A sharp-edged orifice (1.077 inches in diameter)…

A: Given data, Diameter of the pipe, D = 2 in = 0.1667 ft Diameter of the orifice in first case, d1 =…

Q: The figure shows a siphon which is used to draw water from a large open tank. If the absolute…

Q: A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: As per given question A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water,…

Q: Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h₁ =…

Q: Find the pressure head at entry of the pipe, when the pressure of flowing water is 125 N/cm? The…

A: It is required to determine pressure head at entry of pipe in Pa

Q: A 300mm * 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

Q: T= 20°C Consider the water reservoir with a siphon as shown in the figure. If d = 0.06 m, D = 0.25…

Q: Water flows steadily through the system shown below. The 4-in. section leads to a throat, followed…

A: Consider the diagram shown below for the given system as shown below. From the continuity equation,

Q: Water is siphoned from the tank shown in the figure. The water barometer indicates a reading of 30.2…

A: According to Bernoulli's principle, the entire mechanical energy of the flowing fluid, which…

Q: (b) A venturi meter with diameter at inlet D, and throat diameter D2, is used for measuring the flow…

Q: A 15-ft-diameter tank discharges water at 50 F through a 2-in.-diameter sharp edged orifice. If the…

A: orifice meter is used to measure the rate of flow through a narrow section Coeffcient for discharge…

Q: Question 4.12 A venturi meter with throat diameter of 100 mm is fitted in a vertical pipeline of 200…

A: Given:d=100 mm =0.1 mD=200 mm =0.2 ms=0.88Q=0.06 m3/s∆z=320 mm =0.32 m NOTE: According to…

Q: Question 2. B la0 mm diameter siphon draws water from the reservoir. Considering that the elevation…

A: givendaimeter of siphon d=10mmh1=2mh2=5.1mρwater =1000Patm=101.3kPa

Q: 3. Assume there is friction head loss in the siphon as shown in the Fig. 2.1, where a = 1 m, b = 4…

Q: 3. In the figure shown, find the head lost from the inlet to the throat. Water Mercury S-13.6

Q: The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated…

A: Given data, Rate of discharge, Q = 200 lps Q = 0.2 m3/s Pressure at A, PA = 206 KN/m2 = 206 x103 Pa…

Q: A Venturimeter has 400mm diameter at the main and 150mm at the throat. If the difference of pressure…

A: Given data Main diameter of venturimeter (D) = 400 mm throat diameter (d) = 150 mm difference in…

Q: C3. An oil of specific gravity 0.88 is flowing through a horizontal venturimeter fitted to a 262 mm…

A: Given, Specific gravity of oil , S =0.88 Diameter of the pipe , D =262mm = 0.262 m Discharge…

Q: аз in. IS installed in a 6 in. pipe-line. The pressure at the entrance to the meter is 10 psi gauge…

A: A venturi meter(diameter) =3 ininstalled in =6 inA1V1=A2V2π4×6122×v1=π4×3122×v2v1=0.25 v2v2=4 v1…

Q: Question (2) As shown in the Figure below, If the discharge was 0.0035 m/s. Calculate the water…

A: Find the level in the water tank. Given data :- Discharge - 0.0035 m^3/sec.

Q: A 30 cm × 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: A venturimeter is a device which is used for the measurement of the discharge in a pipe. The…

Q: The tube has a diameter of 0.4m, suddenly expanding to a diameter of 0.8m, and the flow rate is 0.4…

Q: A 300 mm x 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

Q: Refining Dept. HW. Lecture 14 Name: QI- Water flows at a rate of 0.040 m/s in a 0.12-m-diameter pipe…

A: (1) Let Q =Discharge =0.04m3/s d1 =Diameter at inlet section =0.12m g =Acceleration due to gravity…

Q: pump with critical cavitation number 0,08 pumps water to a total head of 60 m and temperature of…

Q: Q2: Find the piezometric head at tank (C), if the discharge in pipe (1) = (65 L/sec). Use (-0.025)…

Q: C3. An oil of specific gravity 0.81 is flowing through a horizontal venturimeter fitted to a 260 mm…

Q: l between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number.…

Q: Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (∊ = 0.00061 m).…

A: Answer: The pressure at point A is 320.854734 kPa.

Q: An oil of specific gravity 0.89 is flowing through a horizontal venturimeter fitted to a 242 mm…

A: Given, specific gravity of the oil , S =0.89 Diameter of the pipe , D =242 mm = 0.242 m Diameter of…

Q: A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward…

A: The venturimeter is a device based upon Bernoulli's equation, and is used to measure the rate of…

Q: A ventunmeter having throat diameter 5.3 cm is provided on a pipe of 10 cm diameter. If oil of…

A: Given that, Throat diameter, d2=5.3 cm=0.053 m Pipe diameter, d1=10 cm=0.1 m Specific gravity of…

Q: An external cylindrical mouthpiece of diameter 150 mm is discharging water under a constant head of…

Q: An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 240 mm…

A: Given details: Soil=0.85Smercury=13.6Dinlet=240mm=0.24mDthroat=98mm=0.098X(mercury level)=835mm of…

Q: Q4) The three water-filled tanks shown in Figure below are connected by pipes as indicated. If minor…

Q: H.W2: Calculate the pressure and velocity at points 2 and 3 for the water pipe shown in Figure D,-14…

Q: external cylindrical mouthpiece of diameter 120 mm is discharging w under a constant head of 6 m. If…

A: Given data : Cd=0.86Cc=0.62Diameter of mouth piece (d)=120 mmHead (h)=6 m

Q: 4: Water flow through a pipe at 5L/s as shown in figure. If gage pressure of 12.5kPa, 11.5kPa and…

Q: C3. An oil of specific gravity 0.85 is flowing through a horizontal venturimeter fitted to a 254 mm…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subpart of a question. Please post…

Q: 2. Oil with a S.G. pf 0.82 is flowing in a pipe under the condition below (see figure). If the total…

Q: C3. An oil of specific gravity 0.88 is flowing through a horizontal venturimeter fitted to a 262 mm…

A: ρoilg hoil=ρHgg hHg⇒ρoilhoil=ρHg hHg⇒hoil=ρHg hHgρoil

Q: Q5:- Calculate the discharge of the system in fig.(4),neglecting all losses except through the…

A: There are two types of losses occur in pipe flow:- 1) major loss -these losses are due to viscous…

Q: A venturi meter with diameter at inlet D1, and throat diameter D2, is used for measuring the flow of…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

Explain each step please

0. In the figure below a manometer uses oil with specific gravity of 0.8.
(a) Calculate the discharge when R =
1 ft.
(b) Repeat the problem if the pipe is inclined at 30° upward.
oil
R
6"
3"
6"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If the pressure in a tank of oil (sp gr 0.85) is 376 kN/m2, what is the equivalent head (a) inmeters of oil; (b) in meters of water; (c) in meters of mercury? maintaining the liquid head h at 5.67 ft, to what pressure PA be raised in order to double the discharge?
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
4. The figure shows a siphon discharging oil (sp.gr.= 0.90). The siphon is composed of75 mm pipe followed by a 100 mm pipe from B to the open discharge at C. The headlosses are: from 1 to 2, 0.35 m; from 2 to 3, 0.20 m; from 3 to 4, 0.75 m. Compute thedischarge and make table of heads at point 1, 2 3 and 4. Use the table below. Show yoursolutions.
At point A where the diameter at of the pipe is 18 cm the pressure reading is 22.5 cm of Mercury. At point B, 3 m lower than A, the diameter is 48 cm and the pressure reading is 50 cm of Mercury. If the total head loss between the two points is 1.50 m, solve for the discharge. Water is flowing through the pipe. subject: hydraulics
Find the pressure head at entry of the pipe, when the pressure of flowing water is 200 N/cm2 The pressure head at entry (Unit in Pascal) =
For the tank in the figure, calculate the volumetric flow of water, which comes out through a pipe, the tank is sealed and there is a pressure of 140 KPa above the water, the depth is h1=2.5M
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
A water flows through a pipe at a certain velocity of the pressure gauge reading is 2 bar. The datum head is given to be 2m. Find the piezometric head, density of wate ris 1000, g= 9.8
Determine pressure head at point point 2&3
What is the maximum height the higher reservoir can sit and be filled using a fixed-speed pump with 1-1/4 HP of input and a 57% efficiency rating at 30 GPM of flow? The suction line is 30ft of 1-1/4” schedule 40 steel pipe. The discharge line is 1” schedule 40 steel pipe and is horizontal for 10 ft.
Gasoline (sg0.67) is flowing at 0.11 m³/s in the fabri- cated tube shown in Fig. 6.19. If the pressure before the con- traction is 415 kPa, calculate the pressure in the smaller tube.
A Venturimeter has 400mm diameter at the main and 150mm at the throat. If the difference of pressure is 250mm of mercury and the meter coefficient is 0.97, calculate the discharge of oil through the Venturimeter. Take specific gravity of oil as 0.75.