Determine the capillary rise of the water in the glass tube of diameter 0.35cm, which is immersed vertically in the glass vessel.The surface tension of water is 0.07213 N/m.Take the contact angle of water as theta = 00 The capillary raise of water in the tube is (unit in m)=

Determine the capillary rise of the water in the glass tube of diameter 0.35cm, which is immersed vertically in the glass vessel.The surface tension of water is 0.07213 N/m.Take the contact angle of water as theta = 00 The capillary raise of water in the tube is (unit in m)=

Name: Determine the capillary rise of the water in the glass tube of diamete
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Determine the capillary rise of the water in the glass tube of diameter 0.35cm, which is immersed vertically in the glass vessel.The surface tension of water is 0.07213 N/m.Take the contact angle of water as theta = 00The capillary raise of water in

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
Determine the capillary rise of the water in the glass tube of diameter 0.68cm, which is immersed vertically in the glass vessel.The surface tension of water is 0.07213 N/m.Take the contact angle of water as = 00 The capillary raise of water in the tube is (unit in m)=
Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m.
The volume of the fluid inside the upright conical tank is 0.8 ft3. (a) Determine the needed volume to fill up the entire container. (b) Determine the height of the air from the peak and base of the tank. (c) If the mass of the fluid is 40 kg, determine its density.
Determine the capillary rise of water in the tube of diameter 0.64 mm when immersed in a tank. Take surface tension between the water and tube as 0.073 N/m. 0.0465 m 46.5087 m 0.0047 m 0.4562 m
A 3-ft-diameter vertical cylindrical tank open to the atmosphere contains 1-ft-high water. The tank is now rotated about the centerline, and the water level drops at the center while it rises at the edges. Determine the angular velocity at which the bottom of the tank will first be exposed. Also determine the maximum water height at this moment.
The gage pressure of the air in the tank shown is measured to be 50 kPa. Determine the differential height h of the mercury column
two vertical parallel glass plates 0.1 mm apart are partially immersed in water. Considering that the water does not reach the upper edges of the sheets and that the liquid completely wets the glass, determine: a) the height that rises in the flat capillary, b) the attractive force between the plates. Consider the width of the sheet l=12cm and density y=72.8*10^-3 N/m
A 0.018-in-diameter glass tube is inserted into mercury, which makes a contact angle of 140° with glass. Determine the capillary drop of mercury in the tube at 68°F.
A conical plug is used to close a 0.1m radius circular hole at the bottom of the tank. The dimension for the plug is 0.4m diameter and 0.3m long. Determine the total vertical force, and its direction, acting on the plug if it is inverted and if the tank contains 600mm of oil having an SG of 0.82.
Determine the excess pressure within spherical droplet 1.5 mm in diameter if the surface tension of water is 0.074 N/m
determine the center of pressure in m of an isosceles triangle plate of base 5 m and altitude 5 m when the plate is immersed vertically in an oil (s=0.8). The base of the plate is 1 m below the free water surface.