9-90. The starter for an electric motor is a full cylinder and has the cross-sectional areas shown. If copper wiring has a density of Peu = 8.90 Mg/m³ and the steel frame has a density of Pst = 7.80 Mg/m³, estimate the total mass of the starter. Neglect the size of the copper wire. Problem 9-90 Steel Copper 80 mm 50 mm 30 mm 100 mm 60 mm

9-90. The starter for an electric motor is a full cylinder and has the cross-sectional areas shown. If copper wiring has a density of Peu = 8.90 Mg/m³ and the steel frame has a density of Pst = 7.80 Mg/m³, estimate the total mass of the starter. Neglect the size of the copper wire. Problem 9-90 Steel Copper 80 mm 50 mm 30 mm 100 mm 60 mm

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 17P: Mercury is poured into a U-tube as shown in Figure P15.17a. The left arm of the tube has...

See similar textbooks

Similar questions

A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
Artificial diamonds can be made using high-pressure, high-temperature presses. Suppose an artificial diamond of volume 1.00 106 m3 is formed under a pressure of 5.00 GPa. Find the change in its volume when it is released from the press and brought to atmospheric pressure. Take the diamonds bulk modulus to be B = 194 GPa.
In about 1657. Otto von Guericke, inventor of the air pump, evacuated a sphere made of two brass hemispheres (Fig. P9.89). Two teams of eight horses each could pull the hemispheres apart only on some trials and then with greatest difficulty, with the resulting sound likened to a cannon firing. Find the force F required to pull the thin-walled evacuated hemispheres apart in terms of R, the radius of the hemispheres, P the pressure inside the hemispheres, and atmospheric pressure P0. Figure P9.89
The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?
A rod extending between x = 0 and x = 14.0 cm has uniform cross-sectional area A = 9.00 cm2. Its density increases steadily between its ends from 2.70 g/cm3 to 19.3 g/cm3. (a) Identify the constants B and C required in the expression = B + Cx to describe the variable density. (b) The mass of the rod is given by m=allmaterialdV=allxAdx=014.0cm(B+Cx)(9.00cm2)dx Carry out the integration to find the mass of the rod.
How many cubic meters of helium are required to lift a balloon with a 400-kg payload to a height of 8 000 m? Take He = 0.179 kg/m3. Assume the balloon maintains a constant volume and the density of air decreases with the altitude z according to the expression air = 0ez/8, where z is in meters and 0 = 1.20 kg/m3 is the density of air at sea level.
How many cubic meters of helium are required to lift a light balloon with a 400-kg payload to a height of 8 000 m? Take Hc = 0.179 kg/m3. Assume the balloon maintains a constant volume and the density of air decreases with the altitude z according to the expression pair = 0e-z/8 000, where z is in meters and 0 = 1.20 kg/m3 is the density of air at sea level.
The pressure at the bottom of a glass filled with water ( = 1 000 kg/m3) is P. The water is poured out and the glass is filled with ethyl alcohol ( = 806 kg/m3). The pressure at the bottom of the glass is now (a) smaller than P (b) equal to P (c) larger than P (d) indeterminate.
The total cross-sectional area of the load-bearing calcified portion of the two forearm bones (radius and ulna) is approximately 2.4 cm2. During a car crash, the forearm is slammed against the dashboard. The arm comes to rest from an initial speed of 80 km/h in 5.0 ms. If the arm has an effective mass of 3.0 kg and bone material can withstand a maximum compressional stress of 16 107 Pa, is the arm likely to withstand the crash?
We stated in Example 11.12 that a xylem tube is of radius 2.50105 m. Verify that such a tube raises sap less than a meter by finding h for it, making the same assumptions that sap's density is 1050 kg/m3, its contact angle is zero, and its surface tension is the same as that of water at 20.0°c.
Mercury is poured into a U-tube as shown in Figure P15.17a. The left arm of the tube has cross-sectional area A1 of 10.0 cm2, and the right arm has a cross-sectional area A2 of 5.00 cm2. One hundred grams of water are then poured into the right arm as shown in Figure P15.17b. (a) Determine the length of the water column in the right arm of the U-tube. (b) Given that the density of mercury is 13.6 g/cm3, what distance h does the mercury rise in the left arm?