Question 5.6 & Question 5.9 9 cmcm5 cmFig. PS.97 cm 1中国联通9:28 AMTextbook phot...f chapter 5.pdf•..5.5. The connections at the ends of bars AB and BC are ball-and-socket joints. Neglectingthe weights of the bars, determine the force in cable DE and the reaction at A.E0.8 m2 mO.2 mPDF2 mB800 NFig. P5.5Both pulleys are fixed to the shaft and as the shaft tums with constant angular5.6velocity, the power of pulley A is transmitted to pulley B. Detemine the horizontal tensionT in the belt on pulley B and the x, y,z components of reaction at the journal bearing Cand thrust bearing D if 6 = 45°.S0 N300 mm 250 mm 200 mmC150 mm80 mm60 N80 NFig.P5.65.7 Locate the centroid of the parabolic area.5.8 Locate the centroid of the shaded area.y-ax?y-hxFig. PS.7Fig. PS.85.9 Find the coordinates of the centroid of the plane region.5.10 Find the location of the centroid of the plane region.75 ·

Answered: 9 cm cm S cm 7 cm

Engineering

Mechanical Engineering

9 cm cm S cm 7 cm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.51P: The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest...

See similar textbooks

Similar questions

Application of Equilibrium Solve for the value of unknown variables Given : P1 = 6.85 KN P2 = 4.65 KN W1 = 6.15 KN/m Unknowns : RAy , RAx ,RBy , MA What is the value of internal shear 2.50m to the right of support A
A ladder AB of length 5m and weight (W) 600N is resting against a wall. Assuming frictionless contact at the floor (B) and the wall (A) the magnitude of the force P required to maintain equilibrium of the ladder is?
Determine the horizontal displacement of joint C. The length, L, of trusses AC, BC is 1,300 mm. The applied force at joint C, is 5.0 kN. The cross-sectional area of both trusses, A, is 360 mm2. The elastic modulus of truss AC, E1, is 135 GPa. The elastic modulus of truss BC, E2, is 150 GPa.
Statics-Two Force Members 1. Determine the force P required to maintain equilibrium of the pulley system, and the reactions at the ceiling. 2. Assume W=1.25kN 3. Show and clearly label all Free Body Diagram to determine solution.
....An electric motor drives a compressor by use of V-belt. The angle of contact on the smaller pulley is 2.89 rad and the belt speed runs at 29.36 m/s. The groove angle of the pulleys is 35°. Determine the tension in the slack side of the belt in N if the belt has a cross-sectional area of 366 mm2, density 1000 kg/m3, and an allowable tensile stress of 2.3 MPa. The coefficient of friction between the belt and the pulley is 0.3
A car skidded off an icy road and became stuck in deep snow at the road shoulder. Another car, of 1400 kg mass, attempted to jerk the stuck vehicle back onto the road using a 5 m steel tow cable of stiffness k = 5000 N/mm. The traction available to the rescue car prevented it from exerting any significant force on the cable. With the aid of a push from bystanders, the rescue car was able to back against the stuck car and then go forward and reach a speed of 4 km/h at the instant the cable became taut. If the cable is attached rigidly to the masses of the cars, estimate the maximum impact force that can be developed in the cable, and the resulting cable elongation. Assume that the steady state force, acting on the rope, is equal to the weight of the car.
Q)Two blocks A=150 N and B=? are connected by a rod at their ends by frictionless hinges as shown in the Fig. Find the weight of block B required for limiting equilibrium of the system, if µ = 0.35 at all sliding surfaces.
2-D PROBLEM: A spherical tank with a radius of 3.41m that has a mass of 28928.644kg was supported in the system shown. Assuming friction and the bar weight is negligible, determine the following: β: 21.774° θ: 46.452° 1. The reaction @ point D. 2. Tension @cable BE 3. The x and y-component of the reaction @ A 4. The reaction @ A
A mass M is under tension from wires CD and DE. If CD is 25º from the horizontal while DE is 30º determine the safe value of mass m if the cross sectional areas of the two wires are 80 and 100mm^2 respectively. Maximum allowable stress for wire CD is 30 MPa and wired DE is 40MPa.
To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=2.0a=2.0 ftft, b=7.0b=7.0 ftft, and c=12.0c=12.0 ftft. The applied forces are F1=1.50F1=1.50 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=60∘θ=60∘ with the horizontal. Neglect the weight of the beam.(Figure 1)
1. What is a Spatial Force System? 2.Three-dimensional equilibrium problems for a rigid body can be solved using what procedure?
Two massless cables, BA andBC, support a 50 lbf block hanging from a ceiling.A. Draw the appropriate free-body diagram ANDsolve for the tension in cables BA and BC.??? = ??? =