9.31 and 9.32 Determine the moment of inertia and the radius of gyration of the shaded area with respect to the x axis. 2 in. 2 in. y 3 in.--3 in. O 2 in. 1 in. 3 in. 3 in. 1 -1 in.

Q: Find (D.O) and the (Deficit (D)) for the stream (B), If: Stream T (C) Deficit (D) CI A C Q (m³/s)…

A: Given data Stream Q(m3/sec) T(°c) Deficit (D) (mg/l) cl(mg/l) A 3.7 21 4.49 0 C 6.2 19 3.58…

Q: A conventional floor system has panel dimensions measured from center-to-center of the beam support…

A: Given;                                                                  ·

Q: Qg:- A horizontal curve with a radius of 200 m forms part of a two-lane highway with a posted speed…

A: The radius of the curve = 200 mThe posted speed = 50 kphThe perception reaction time = 2.5 secThe…

Q: What should be the diameter of sewer (in m) if it is designed to carry a discharge of 0.75 cumec…

A: Discharge Q=0.75 cumec running half full,Manning's coefficient n=0.016Gradient of the pipe = 1 in…

Q: Q2 At 20°C, there is a gap A=0.2 mm between the lower end of the bronze bar and the rigid slab…

A:

Q: A rectangular foundation of plan size 5 (B) × 10 (L) m is to be designed to carry a load of 86.6 MN…

A: Width of the footing, B = 5m , Length of footing , L = 10m , Dry Unit Weight,Saturated Unit Weight ,…

Q: •JORN THAT T Im 2m 2mm 1mf 40 mm 1.) Draw the shew and 28 Find to 3.) Flexural Date Flexural…

A: As per company's guidelines we can only answer first three questions. Kindly post other questions as…

Q: Q4-The stream flows due to three successive storms of 2.9, 4.9 and 3.9 cm of 6 hours duration each…

A: Given;Three storm of intensity 2.9,4.9 and 3.9 cm of 6 hr. duration each. Area of basin (A) = 118.8…

Q: The maximum super-elevation to be provided on a road curve is 1 in 15. If the rate of change of…

A: Note- It is required to solve only the first problem.Maximum super-elevation e=1/15,Rate of change…

Q: B) The rates of rainfall for the successive 30 min period of a 3-hour storm are: 1.6, 3.6, 5.0, 2.8,…

A:

Q: Assuming the reaction torque at A is TA (kip.in)(), TA<16(kip.in) express the magnitude of (i) the…

A: Torque, T = 16 kip-in Modulus of rigidity, GA = 3.8*106 psi Modulus of rigidity, GB = 5.4*106 psi a…

Q: 1. What is the limit of economic haul in stations? 2. What is the total cost in dollars for…

A: Find:(a) Limit of economic haul in stations(b) Total cost in dollars for excavation(c) Overhaul cost…

Q: A national highway passing through rolling terrain in heavy rainfall area has a horizontal curve of…

A: Speed V=80 kmph Pavement width w=7 m Centrifugal acceleration α=0.52 m/s2 Radius R=450 m Length of…

Q: How does one go about testing a structural database, and how does this mode of testing vary from…

A: Database Structural Testing Testing a structural database involves verifying its…

Q: Determine the sliding factor of safety and the heel and toe stresses for a riangle gravity dam (25m…

A: To find: The sliding factor of safetyheel stresstoe stress

Q: 13-14 Rods AC and BC are used to su which the average normal stress can not exceed 150 Mpa What is…

A: mass of block m =200kg normal stress =150MPa

Q: -36 kNm 2 m X→- 2m +36 kNm 3 m -50 kNm -40 kNm + moment

A: We have to determine the value of X

Q: 6m note: Moment acts 1m from the free end. 20 kN/m 6m 700 kN-m 40 kN/r

A:

Q: Consider Euler's equation for one-dimensional (horizontal) unsteady flow. In a 20 cm diameter…

A:

Q: 6-69. Determine the maximum moment at C caused by the moving load. 12 kN Bla 1 m -0.5 m 8 m 4 m B

A: The below beam figure is shown,To determine:-The maximum moment at C caused by the moving load.

Q: You are asked to design a horizontal curve for a four-lane road. The road has 12-ft lanes. Due to…

A: The width of the lanes = 12 ftThe number of lanes in the road = 2 lanesThe maximum clearance from…

Q: Determine the slope and deflection at point C of the beam shown by the direct integration method and…

A: Overhang beam with two point loads    NOTE : The question is solved by direct integration method…

Q: Q4/ The pressure drop in a certain length of 0.3 m horizontal waterline is 68.95 kPa when the mean…

A: Horizontal waterline length =0.3 m, Pressure drop=68.95 kPa, Mean velocity V=4.5 m/s, Water…

Q: 6 Which of the following gives the reaction at C in the given beam? 300N 210 N/m A 100 Nm TITT 5m B…

A:

Q: How might a brick-and-mortar store implement FBA?

A: Fulfilment By Amazon (FBA) is a service offered by Amazon that allows sellers to store their…

Q: Determine the displacement at point C. Use the principle of virtual work. El is constant. 12 kN/m

A: The beam with loading and support conditions is given as EI = Constant To find:- Displacement at…

Q: A y 6 ft B + 5 kips/ft El= constant 6 ft

A:

Q: Determine the Q.T.O for the reinforcement for the following drilled pier 8-20M DOWELS, 500 INTO PIER…

A: Pile diameter, D = 500 mm Cover thickness, c = 50 mm Stirrups spacing = 400 mm center to center…

Q: Glycerine (specific weight 1260 kg/m³, dynamic viscosity 8.00 x 10-2 kg-s/m²) is spread freely to a…

A:

Q: A spherical object of diameter 0.6 m is placed in a body of water. It was observed that the topmost…

A:

Q: A plate is used as a tension member, to carry a deadload = 300 KN and live load of 260 KN. Steel…

A: Dead Load = 300 kN and Live load = 260 kNFy = 248 MPa and Fu = 400 MPa and width of tension plate  =…

Q: Q3 Analyze the structure shown in Figure (3), using Slope-Deflection Method, (support d settles by 1…

A: As per the honor code, the first problem will be solved. Fixed end moment: Span ab:…

Q: The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if…

A: For small angles.

Q: A concrete dam cross-section is given in the Figure. Check the stability of the dam

A:

Q: With the transit at point A and the line of sight horizontal, the stadia intercept at B was found to…

A: question 3 and 4 both are separate question .they are not linked with each other. hence here answer…

Q: Question 2: True or False? Please give simple reason for each of them. (1) Diffusion is a time and…

A: (1) True. Diffusion is a time and temperature-dependent phenomenon by atomic transport. Diffusion…

Q: 10 kNm A 4 m B 4 4 m C 4 m 5 kN D 100 mm 80 mm

A:

Q: Determine the flexural capacity of the given section of beam below. b=350 d=615 d'=100 fc'=34 fy=415…

A: b=350d=615d'=100fc'=34fy=415As=5-36mmAs'=2-25mmIt is asked to determine the flexural capacity of the…

Q: A primary sedimentation sludge has a moisture content of 95% and 65% of the dry solids are volatile.…

A: A primary sedimentation sludge has a Moisture content of 95% and 65% of the dry solids are volatile.…

Q: Q3:- A parabolic vertical curve joins a grade of -3% to a grade of +5.5 %. The PVI is at station…

A: The downward gradient (g1) = -3% = -0.03   The upward gradient (g2) = +5.5% = 0.055The station of…

Q: Q.2 There are 2 primary settling basins each 24 m in diameter with a side water depth of 2.1 m…

A: 2 primary settling basins- Diameter of basin D = 24 m, Side water depth H = 2.1 m single effluent…

Q: A 6 m C -10 m- Probs. 6-67/68 30 kN B 80 KN 60 KN 2 m 30 kN -1 m

A:

Q: Q9:- For the following intersection, it has been decided to use a traffic signal device. The…

A: Given;Amber flow = 3 secWithout all red time; starting delay = 2.5 sec                  .

Q: Normal hydraulic jump has a sequent depth ratio of 8.0. The initial depth is 0.5 m. What is the…

A:

Q: Two vertical identical conical tanks (both inverted) have their vertices connected by a short…

A: Tank-1 is fully filled with waterTank-2 is filled only upto depth 1 m.Given;Base diameter is 2…

Q: T 3 m İ 3m 50 kN 1 5 3 -3m-x e 2 6m 6 m 6 6 m

A:

Q: Question 7 A simply supported beam made of timber is shown; determine the minimum required width b,…

A:

Q: A septic tank of 7 m³ in volume serves for 5 accumulation of sludge is people. If the rate of 70…

A: Volume of the septic tank (V) = 7 m3,Number of people (n)= 5 Rate of accumulation of sludge = 70…

Q: What is yield strength? 2. What is tensile strength? 3. Explain Deflection of beams in terms of…

A: Yield strength and tensile strength are two important properties to consider in material selection…

Q: A double drain consolidation test was performed on a sample of marine clay. The thickness of the…

A: Double drainH = 50 mmk = 1.753x10-8 m/min = 300 KN/m2  = 500 KN/m2 e1 = 0.42e2 = 0.3

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.