A 10 cm conical pointed shaft turns in a stationary conical bearing with an angular velocity of 5 rad/s. An oil of viscosity 0.036 N.s/m² fills a 2 mm gap between the shaft and the bearing. Find the shear stress acting on the surface of the conical shaft. Also, calculate the viscous torque on the shaft.

A 10 cm conical pointed shaft turns in a stationary conical bearing with an angular velocity of 5 rad/s. An oil of viscosity 0.036 N.s/m² fills a 2 mm gap between the shaft and the bearing. Find the shear stress acting on the surface of the conical shaft. Also, calculate the viscous torque on the shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Nitrogen gas at 15 oC has a density of 0.07616 lbm/ft3 with a kinematic viscosity of .146 cm2 /s forms a boundary layer near a solid wall. The velocity distribution in that boundary layer is given by the expression ?/? = 1 − ?^(−2?/?) where U = 15 m/s and δ = 1.2 cm. Find the shear stress at the wall (y=0.005 m).
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). And when the shaft is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kiloWatts (kW).
Glycerin, with a density of 1260 kg/m3 and an absolute viscosity of 1.5 kg/m.s, flows in a tube with an internal diameter of 5,0 cm, but it is not known whether the regime is laminar or turbulent. Knowing that the length of the hydrodynamic inlet of this flow is 0.2 m, determine the velocity of the oil and the flow regime. (the form is in the side picture)
The belt in the Ögure moves at steady velocity V and skims the top of a tank of oil having viscosity. (a) Develop and expression for the required belt drive power in terms of h, L, b, V , and . Recalthat, for steady motion, power is equal to force velocity.(b) What power is required if the belt moves at 5 m/s over SAE 50W oil ( = 0:86 kg/ms) withh = 2 cm, L = 2 m, and b = 0:5 m
What is the minimum surface tension of a fluid that can sustain a gauge pressure of 0.1 kPa in a 0.5 cm radius bubble?
Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
The 1-m-diameter tank in Fig. is initially filled withgasoline at 20°C. There is a 2-cm-diameter orifice in thebottom. If the orifice is suddenly opened, estimate the timefor the fluid level h(t) to drop from 2.0 to 1.6 m.
A piston with a diameter of 6 cm and a length of L = 13 cm rotates at n = 105 rpm in a cylinder of 6.04 cm in diameter as shown in the figure. Since the dynamic viscosity of the oil between the piston and the cylinder is 1.075 kg · sec · m-2, calculate the moment value that should be applied to the piston rod. M=?
the velocity principle of a given fluid flowing over a flat plate is given by = 2y – y 2 , where u in inches and y in inches .find shear stress at y = 0 and 1 ,respectively , if the fluid viscosity is 0.006 lbf s/ft 2 .
What is Reynold’s number? What is its relevance in fluid flow. Define viscosity and ts properties.
pllllzzzz help me right nowww plzzz The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?
Honey at 1L/min is flowing in a capillary viscometer 2cm in diameterand 50cm long. If the pressure drops is 40kPa, determine its viscosity