Please answer all parts legibly, thanks! 1. A 10 m simply supported beam caries a uniform load of21kN/m and concentrated load of 50 kN located at themidspan. The cross-sectional area of the beam is shown below,determine the following:a. Maximum momentb. Location of neutral axis from the top fiberc. Moment of inertiad. Maximum flexural stress

Answer We are given length of beam L = 10m uniform load w = 21 KN/m Concentrated load P = 50 KN…

A 10 m simply supported beam canies a uniform load of 21kN/m and concentrated midspan. The cross-sectional load of 50 kN located at the area of the beam is shown below, determine the following: a. Maximum moment b. Location of neutral axis from the top fiber c. Moment of inertia d. Maximum flexural stress

A 10 m simply supported beam canies a uniform load of 21kN/m and concentrated midspan. The cross-sectional load of 50 kN located at the area of the beam is shown below, determine the following: a. Maximum moment b. Location of neutral axis from the top fiber c. Moment of inertia d. Maximum flexural stress

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the beam is subjected to an internal moment of M = 40 kN . m, determine theresultant force caused by the bending stress distribution acting on the top flange A.
DRAW the elastic curve of the beam. Flexural rigidity is 415 kN-m^2
A beam ABCDE is 10 m long and is simply supported at B and the extreme right-hand endE. The beam carries point loads of 50 kN on the over-hanging end at A and 60 kN at D,together with a uniformly distributed load of 40 kN/m between B and C. AB = DE =2m, and BC = 4m. If the point C is 2 mm below the level of the supports at B and E.Determine:(a) The flexural stiffness EI. (b) The deflection at the end A.
If the beam carries a moving uniform load of 136 kN/m and concentrated moving load of 114 kN. Using theinfluence line diagram, (a) determine the maximum +M due to loads at C (b) determine maximum +V at C
A overhang beam hanged at B(6m) has two loads of 8 & 4 kn at 6 and 9 m. Calulate its moment using castigliano's theorem.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 17 cm as width, 28 cm as depth and inner thickness as 2 cm is subjected to a point load of 7 N & 5 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 2 m & CD = 2 m. i) Reaction force at B in (N)= ii) Reaction Force at A in (N) = iii) The distance from B at which the shear Force value changes from "-" to "+" in (m) = iv) Maximum Bending Moment (Please write the Maximum bending moment valve in (Nm) = v) Moment of Inertia, I in (m^4)= vi) Maximum bending stress in (N/m^2)= vii) Bending stress at 2 cm from the top in (N/m^2) =
The Beam has a span of 9 m, fixed at both ends and carries a uniformly distributed load of w = 25 kN/m throughout its length. The beam is W 16 x 77 with the following properties: bf = 260 mm tf = 19.3 mm d = 420 mm tw = 11.6 mm Ix = 462. 02 x 106 mm4 Iy = 57.44 x 106 mm4 a. Calculate the maximum bending stress in the beam, in MPA. b. Calculate the average shearing stress in the web, in MPa.
The steel beam has the cross-sectional area shown. if w = 6.5 kips/ft, determine the absolute Horizontal shearing stress (ksi) in the beam Where L1 = 9 ft; L2 = 8 ft; bf = 8.2 in and tw = 0.4 in
A propped beam has a span of 7.2 meters is simply supported at C. It carries a concentrated load of 60 kN, 3 meters from C. EI = 3000 kN.m2. reaction at C, in kN angle of rotation at C deflection at B, in mm
Determine the moment M in kN-m that must be applied to the beam to create maximum stress of 99 MPa. Where tf = 17 mm and d = 302 mm
1. A 75 mm x 75 mm x 8 mm angle is used as a beam over a span of 7.0 m. It is subjected to loading of 10 kN/m acting in the vertical plane passing through the centroid of the Section Determine maximum stress induced in the section.
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 16 cm as width, 23 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 7 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =