Please solve all questions please this one is much urgent please please please A 2.5 x 2.5-inch sleeve bearing uses grade 20 lubricant. The axial-groove sump has a steady-state temperature of95 F. The shaft journal has a diameter of 2.500 in with a unilateral tolerance of -0.001 in. The bushing bore has adiameter of 2.504 in with a unilateral tolerance of 0.001 in. The journal speed is 900 rev/min and the radial load is 1400Ibf.1) Estimate the film temperature.2) Estimate the minimum film thickness.3) Estimate the eccentricity.4) Estimate the coefficient of friction.

Answered: Image /qna-images/answer/5718a045-7408-4c0c-aebf-3a63be389310.jpg

Answered: A 2.5 x 2.5-inch sleeve bearing uses…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to raise the load without friction effect? Group of answer choices 66845 N-mm 133690 N-mm 236078 N-mm 334840 N-mm
Q 2. A journal bearing has a shaft diameter of 75.00 mm with a unilateral tolerance of −0.02 mm. The bushing bore has a diameter of 75.10 mm with a unilateral tolerance of 0.06 mm. The bushing is 36 mm long and supports a load of 2 kN. The journal speed is 700 rev/min. For the minimum clearance assembly find the minimum film thickness, the heat loss rate, and the maximum lubricant pressure for SAE 30, SAE 40 and SAE 50 lubricants operating at an average film temperature of 60 °C.
A full journal bearing has a nominal diameter of 60.0 mm, a bearing length of 30.0 mm and supports a load of 3200 N when running at the design speed of 3200 rpm. The radial clearance has been specified as 0.04 mm. An SAE 20 oil has been chosen and the lubricant supply system is capable of delivering the lubricant to the bearing at 60oC. Using the Raimondi and Body design charts;1.1 find the temperature rise of the lubricant, (19)1.2 the total flow rate required, (1)1.3 the torque required to overcome friction (3)1.4 and the power dissipated in the bearing.
A double square thread power screw is to raise a load of 70 kN. The screw has a mean diameter of 33.375 mm and a pitch of 6 mm. The coefficient of thread friction and collar friction are 0.13 and 0.10, respectively. The collar mean diameter is 90 mm and the screw turns at 90 rpm. Which of the following is the torque required to overcome the collar friction? Group of answer choices 630000 N mm 315000 N mm 819000 N mm 409500 N mm
It has a full-slide type bearing rotating at a speed of 1975 rpm.A load of 5693 N is applied. SAE 40 oil in bearing at 60C inlet temperatureplanned to be used.Shaft and bushing diameters in bearing with tolerance data 41−0.010 respectively+0.000mmand 41.125−0.000+0.100 mm.Average radial clearance mounting for this bearing with bush length 20.50 mmCalculate the following;a) Bearing characteristic number,b) Minimum lubricant film thickness,c) Eccentricity value,d) coefficient of friction,e) Average oil film temperature andf) Find the Tmax temperature value.
Please answer part 2, A 20° full depth involute spur pinion of 4 mm module and 21 teeth is to transmit 15 kW at 960 rpm. Its face width is 25 mm. 1.The tangential force transmitted (in N) is (a) 3552 (b) 2611 (c) 1776 (d) 1305 2. Given that the tooth geometry factor is 0.32 and the combined effect of dynamic load and allied factors intensifying the stress is 1.5 the minimum allowable stress for the gear material in MPa is, (a) 242.0 (c) 121.0 (b) 166.5 (d) 74.0
A steel shaft 800 mm long transmitting 15 kW at 400 r.p.m. is supported at two bearings at the twoends. A gear wheel having 80 teeth and 500 mm pitch circle diameter is mounted at 200 mm from theleft hand side bearing and receives power from a pinion meshing with it. The axis of pinion and gearlie in the horizontal plane. A pulley of 300 mm diameter is mounted at 200 mm from right hand sidebearing and is used for transmitting power by a belt. The belt drive is inclined at 30° to the vertical inthe forward direction. The belt lap angle is 180 degrees. The coefficient of friction between belt andpulley is 0.3. Design and sketch the arrangement of the shaft assuming the values of safe stresses as :τ = 55 MPa; σt= 80 MPa. Take torsion and bending factor 1.5 and 2 respectively.
A drilling machine is capable of drilling 30 holes of 20mm diameter per minute in a 16mm thick steel plate.Theplate has an ultimate shear strentgh as 360 N/mm2. The calculated energy for this process is 2895.2 Nm.Actual drilling process continues during the 36° rotation period of the crank shaft. This crank shaft is driven by a flywheel through a reductionn gear with a ratio of 1:8.In this case the rotation speed is 240 rpm related to the given cycle ratio. Mechanic gain is 80%. Speed fluctuation coefficient is 0.01and flywheel diameter is 0.75m.(a) Find the required power?(b) Find the energy change ΔEk? (c) Find the mass of the flywheel?
A fan is driven by a belt from a motor which runs at 880 rpm. A medium double ply leather belt 5/16 inches thick and 10 inches wide is used. The diameters of the motor pulley and the driven pulley are 14 inches and 54 inches, respectively. The center distance is 54 inches and both pulleys are made of cast iron. Coefficient of friction of leather on cast iron is 0.35. The allowable stress of the belt is 350 psi and the belt weighs 0.035 lb/in^3. What is the horsepower capacity of the belt?
A 17-tooth 20° pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth disk gear. The diametral pitch is 10 teeth/in, the face width 1.5 in, and the quality standard is No. 6. The gears are straddle-mounted with bearings immediately adjacent. The pinion is a grade 1 steel with a hardness of 240 Brinell tooth surface and through-hardened core. The gear is steel, through-hardened also, grade 1 material, with a Brinell hardness of 200, tooth surface and core. Poisson's ratio is 0.30, Jp = 0.30, JG = 0.40, and Young's modulus is 30(10°) psi. The loading is smooth because of motor and load. Assume a pinion life of 108 cycles and a reliability of 0.90, and use YN = 1.3558N-0.0178, ZN = 1.4488N-0.023. The tooth profile is uncrowned. This is a commercial enclosed gear unit. (a) Find the factor of safety of the gears in bending. (b) Find the factor of safety of the gears in wear. (c) By examining the factors of safety, identify the threat to each gear and to the…
A 21-tooth pinion rotating at 1000 rpmrpm meshes with a 33-tooth gear in a spur-gear reducer. Both pinion and gear are manufactured to a quality level of 9. A reliability of 0.9 has been specified and the transmitted tangential load is 2500 lblb. Conditions are such that Cm= 1.7. It is proposed that standard 25∘∘, full-depth teeth be used, with both pinion and gear hobbed from an AISI 4140 nitrided steel. The diametral pitch is 6, and the face width 2.000 inin. Suppose that the life of the pinion will be less than that of the gear, the lubricant bulk temperature does not exceed 250∘F∘F, both driver and driven devices are smooth-running, the gearset is external, gears made by conventional methods. Use the average value for the uncorrected surface-fatigue strength when choosing it from the appropriate table. Assume that the reducer is used for critical service applications. a)What is the dynamic factor (Cv) for the pinion? b)What is the AGMA Surface-Geometry Factor(I) for the pinion/gear…
A pair of gears with 14.5° full-depth teeth are to transmit 5 hp at 1800 rpm of the pinion; mw= 2.5; Np = 20 teeth; carefully cut teeth; intermittent service; Kf= 1.45. A. Determine the diametral pitch, B. face width, C. and tooth numbers if the pinionis to be made of phosphor gear bronze (SAE 65, Table AT 3

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS