A 20-cm-diameter, 60-cm-high vertical cylindrical container, shown in side Figure, is partially filled with 50-cm high liquid whose density is 850 kg/m³. Now the cylinder is rotated at a constant speed. Determine the rotational speed at which the liquid will start spilling from the edges of the container.

A 20-cm-diameter, 60-cm-high vertical cylindrical container, shown in side Figure, is partially filled with 50-cm high liquid whose density is 850 kg/m³. Now the cylinder is rotated at a constant speed. Determine the rotational speed at which the liquid will start spilling from the edges of the container.

Name: Question 5:A 20-cm-diameter, 60-cm-high vertical cylindrical containe
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Question 5:A 20-cm-diameter, 60-cm-high vertical cylindrical container,shown in side Figure, is partially filled with 50-cm high liquidwhose density is 850 kg/m³. Now the cylinder is rotated at aconstant speed. Determine the rotational speed at whic

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure and detailed solution.
Consider a hollow cube of side length 22 cm, fi lled completelywith water at 20 ° C. The top surface of the cube ishorizontal. One top corner, point A , is open through a smallhole to a pressure of 1 atm. Diagonally opposite to point Ais top corner B . Determine and discuss the various rigidbodyaccelerations for which the water at point B begins tocavitate, for ( a ) horizontal motion and ( b ) vertical motion.
The distance between the centers of the two arms of a U-tube open to the atmosphere is 30 cm, and the U-tube contains 20-cm-high alcohol in both arms. Now the U-tube is rotated about the left arm at 3.5 rad/s. Determine the elevation difference between the fluid surfaces in the two arms.
A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure. Please be clear and write explanation in every solution. Thank you.
A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure.
Two thin flat plates, tilted at an angle α , are placed in a tankof liquid of known surface tension Y and contact angle θ ,as shown in Fig. C1.3. At the free surface of the liquid inthe tank, the two plates are a distance L apart and havewidth b into the page. The liquid rises a distance h betweenthe plates, as shown.( a ) What is the total upward ( z -directed) force, due to surfacetension, acting on the liquid column between theplates?( b ) If the liquid density is ρ , fi nd an expression for surfacetension Y in terms of the other variables.
A narrow, U-shaped glasstube with open ends is filled with25.0 cm of oil (of specific gravity0.80) and 25.0 cm of water on oppositesides, with a barrier separating theliquids (Fig.). (a) Assume thatthe two liquids do not mix, and find thefinal heights of the columns of liquid ineach side of the tube after the barrier isremoved. (b) For the following cases,arrive at your answer by simple physicalreasoning, not by calculations:(i) What would be the height on eachside if the oil and water had equal densities? (ii) What would the heightsbe if the oil’s density were much less than that of water?
A bottle consisting of a cylinder 30 cm in diameter and 30 cm high has a neck 5 cm in diameter and 30 cm long. If the bottle, filled with air under normal atmospheric condition, is inverted and submerged in water until the neck is just filled with water, find the depth to which the open end is submerged. Neglect vapor pressure.
Consider two identical glasses of water, one stationary and the other moving on a horizontal plane with constant acceleration. Assuming no splashing or spilling occurs, which glass will have a higher pressure at the (a) front, (b) midpoint, and (c) back of the bottom surface?
Calculate the density of water vapor at 350 kPa abs and 20C if its gas constant is 0.462 kPa-m3/kg-K
Make an explanation for every solution. and please be clear with your numerical solution. Problem: A bottle consist of a cylinder 35 cm in diameter and 30 cm high and a neck 5 cm in diameter and 30 cm long. The bottle is inserted into a body of water, with the open end of the neck first until the neck is completely filled with water. Assuming the pressure of the atmosphere is standard, and neglecting vapor pressure, what is the depth to which the open end is submerged below the free surface? Show correct figure.
The density of stainless steel is about 8000 kg/m3 (eight times denser than water), but a razor blade can float on water, even with some added weights. The water is at 20oC. The blade shown in the photograph is 4.3 cm long and 2.2 cm wide. For simplicity, the center cut-out area of the razor blade has been taped so that only the outer edges of the blade contribute to surface tension effects. Because the razor blade has sharp corners, the contact angle is not relevant. Rather, the limiting case is when the water contacts the blade vertically as sketched (effective contact angle along the edge of the blade is 180°). (a) Considering surface tension alone, estimate (in grams) how much total mass (razor blade + weights placed on top of it) can be supported. (b) Refine your analysis by considering that the razor blade pushes the water down, and thus hydrostatic pressure effects are also present. Hint: You will also…