A 3003-H14 aluminum alloy rod with 15 mm diameter is subjected to a 9-kNtensile load. Calculate the resulting diameter of the rod. If the rod is subjectedto a compressive load of 9 kN, what will be the diameter of the rod? Assumethat the modulus of elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yieldstrength is 145 MPa.

A 3003-H14 aluminum alloy rod with 15 mm diameter is subjected to a 9-kNtensile load. Calculate the resulting diameter of the rod. If the rod is subjectedto a compressive load of 9 kN, what will be the diameter of the rod? Assumethat the modulus of elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yieldstrength is 145 MPa.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

The frame of a space shuttle type vehicle must have a high yield strength and high stillness, and the most important design factor is weight. Of all the materials presented in this chapter, what material might be the most suitable for the frame of a space shuttle? Assume that there will be both tensile and compressive stresses. For a space shuttle, cost is not a limiting factor. (a) You can eliminate entire classes of materials from consideration with a brief statement about their unsuitability. (b) What material has the highest specific yield strength? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (c) What material has the highest specific elastic modulus? Give the yield strength, specific gravity, specific yield strength, elastic modulus, and specific elastic modulus for this material. (d) Compare the materials with the highest specific yield strength and highest specific elastic modulus for suitability in the space shuttle frame. (C) Discuss the suitability of the top-rated material for this design from the viewpoint of the ability to produce a frame.
According to Figure 5-20, is ii possible to completely separate one of the four materials from the other three? Explain your answer.
A 3003-H14 aluminum alloy rod with 0.5 in. diameter is subjected to a 2000- lb tensile load. Calculate the resulting diameter of the rod. If the rod is sub- jected to a compressive load of 2000 lb, what will be the diameter of the rod? Assume that the modulus of elasticity is 10,000 ksi, Poisson’s ratio is 0.33, and the yield strength is 21 ksi.
An aluminum rod has a cross-sectional area of 0.19635 in2. An axial tensile load of 6000 lb. causes the rod to stretch along its length, and shrink across its diameter. What is the diameter before and after loading? answers in inches. complete solution with fbd
An aluminum alloy cylinder with a diameter of 76 mm and a height of150 mm. is subjected to a compressive load of 220 kN. Assume that the material is within the elastic region and a modulus of elasticity of 75 GPa.a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?
An aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 * 106 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded
A metal rod with 10 mm diameter is subjected to 9 kN tensile load. Calculatethe resulting diameter of the rod after loading. Assume that the modulusof elasticity is 70 GPa, Poisson’s ratio is 0.33, and the yield strength is 145 MPa.
A cylindrical rod of Aluminum (E = 70GPa) is to be subjected to a load of 9000N. If the deformation is entirely elastic,what must the diameter be to allow anelongation of 1.50mm in a length of500mm? (in mm) Show the complete solution and formulas used.
An aluminum alloy cylinder with a diameter of 3 inches and a height of 6 inches issubjected to a compressive load of 50,000 pounds. Assume that the material is within theelastic region and a modulus of elasticity of 11 x 106 psi.a. What will be the lateral strain if Poisson’s ratio is 0.33?b. What will be the diameter after load application?c. What will be the height after load application?
A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.1 mm and the diameter was changed to 9.9967 mm,calculate the modulus of elasticity and Poisson’s ratio.
A wood beam is strengthened using two steel plates as shown in the figure below. *Inserted Photo* The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. Calculate the maximum tensile and compressive stresses of the beam. Assume that Ew = 11 GPa and Es = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood ? MPa maximum tensile stress in steel ? MPa maximum compressive stress in wood ? MPa maximum compressive stress in steel ? MPa