A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.1 mm and the diameter was changed to 9.9967 mm,calculate the modulus of elasticity and Poisson’s ratio.

A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.1 mm and the diameter was changed to 9.9967 mm,calculate the modulus of elasticity and Poisson’s ratio.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Related questions

Q: Problem 7.1. The aluminum bar (cross section 3 cm x 3 cm) shown the figure below is loaded to its…

A: When the axial load is applied to the specimens or the element of any wood or iron material. It…

Q: A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If…

A: It is required to determine the stress in the rod. Here, P is the load and A is the area of the…

Q: Two gage marks are placed exactly 250 mm apart on a 12-mm diameter aluminum rod. Knowing that, with…

Q: A metal rod with 0.5 in. diameter is subjected to 2000 lb tensile load. Calculate the resulting…

A: The given data is shown below:

Q: A rod of dimension 20 mm x 20 mm is carrying an axial tensile load of 10 kN. If the modulus of…

A: given force F=10 kNE=250 MPacross section area A=20 mm×20 mm

Q: During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile…

A: To find modulus of elasticity and Poisson's ratio

Q: A steel bar 4 inches long and having a square cross section 0.8 inches on an edge is pulled in…

Q: Q5 A specimen of magnesium having a rectangular cross section of dimension= (3.2 mm X 19.l mm) and…

A: load extension stress=PA strain=δll 0 0 0 0 1380 0.03…

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: The given data is: Tensile Load on metallic bar (P) = 190 kN Diameter of bar (d) = 16 mm Length of…

Q: A rectangular bar 10millimeters in Length and 20 millimeters in width is held at its upper end. The…

A: Strength of material: It refers to different numerical methods stresses and strains in structural…

Q: Calculate the stress in a No. 7 rebar subjected to a tensile load of 10,600 lb.

A: It is a carbon-steel frequently used to reinforce the medium to heavily loaded reinforced…

Q: A steel column of diameter 100 mm and length 250 mm when subjected to an axial compressive load of…

Q: } 8) A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm². If a…

Q: Problem :6 Diameter of the metal bar, before and after load application was measured to be 100.00 mm…

Q: u, A tensile load of 3000 N is applied to a steel bar of cross-sectional area 500 mm. If a tensile…

Q: A steel bar of 500 mm length is under tensile stress of 100 N/mm?. If the modulus of elasticity is 2…

A: Given data : Length (L)=500 mmTensile stress (σ)=100 N/mm2Modulus of elasticity (E)=2×1011 N/mm2

Q: A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and…

Q: Measurements should be reported to the nearest 1000, 100, 10, 1, 0.1, 0.01,0.001 units, etc.,…

A: The measurements are reported depending on their variability and intended use as follows. a) The…

Q: Impact value is used to measure? А. Hardness В. Toughness C. Wheel load D. Strength

A: To find out the impact value is used to measure.

Q: If the modulus of elasticity for a given material is twice its modulus of rigidity, then bulk…

A: Given data : Modulus of elasticity=E Modulus of rigidity=C E=2C

Q: tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. by 0.6 in. cross section and a…

Q: A tensile test is performed on a brass specimen 10mm in diameter using a gage length of 50mm When…

Q: Problem # A tensile load of 220 KN is applied to a round metal bar with a diameter of 16 mm and a…

A: Data given: Tensile load = 220 kN = 220 × 103 N Diameter of the bar ϕ= 16 mm gauge length L = 50 mm…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: A metal rod with 10 mm diameter is subjected to 9 kN tensile load. Calculatethe resulting diameter…

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of…

Q: During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a…

A: Given data : Initial Length (Li)=6 inInitial area (AI)=0.32 in2Tensile load (P)=50000 lbsFinal area…

Q: A steel rod has a length of 4 ft, and a diameter of 3 inches. Determine the amount of stress in the…

A: Given data : Length (L)=4 ftDiameter (d)=3 inForce (F)=5000 lbModulus of elasticity (E)=30×106 psi

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and…

Q: A metal specimen 36-mm in diameter has a length of 360 mm. A force of 300 KN elongates the length by…

Q: A specimen is originally 1ft long, has a diameter of 0.5in, and is subjected to a force of 5001b.…

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Q: If a steel column with cross-sectional area A = 1000 mm^2 modulus of elasticity E = 200 MPa and…

Q: A copper rod with a diameter of 19 mm, modulus of 110 GPa, and a Poisson’sratio of 0.35 is subjected…

A: Given: The diameter of copper d, is 19 mm. Poisson’s ratio is 0.35. The reduction is diameter is…

Q: An alloy has a yield strength of 41 ksi, a tensile strength of 57 ksi, and an elastic modulus of 16…

A: Given: The diameter of the cylindrical specimen is 0.5 in. The length of the cylindrical specimen is…

Q: A 5ft long rod with a 0.63 inch diameter is subjected to a 10,661lb tensile load. What is the…

A: Given data, Length of rod = 5 ft Diameter of rod = 0.63 inch Tensile load = 10661 lb To find out…

Q: The elastic portion of the force-extension diagram for a specimen under uniaxial loading is shown in…

Q: A cylindrical specimen of brass that has a diameter of 20 mm, a tensile modulus of 110 GPa, and a…

Q: Two gage marks are placed exactly 250 mm apart on a 12-mm diameter aluminum rod. Knowing that, with…

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of…

Q: A specimen of ductile cast iron having a rectangular cross section of dimensions 4.8 mm x 15.9 mm is…

A: Modulus of elasticity can be defined as the ratio of the stress experienced by a body or in a body…

Q: A cylindrical rod 600 mm long and having a diameter 13.2 mm is to be subjected to a tensile load. If…

Q: Q1: The original length of a piece of metal is 400 mm, this piece has pulled in tension with stress…

Q: A steel rod, 12mm in diameter and 150mm long was subjected to a tensile test. After the test, the…

Q: A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of…

Q: A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength…

A: aWe knowΔL=PLAE0.1=5.851000100π4102EE=74,485Nmm2E=74,485Mpa

Q: A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length…

A: For the given metal bar,

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?
A cylindrical rod of steel (E = 207 GPa),4mm in diameter is to be deformed by atensile force. Determine the force (in N)that will produce an elastic reduction of2.5 x 10-3mm in diameter if Poisson’sratio is 0.30. Show complete solution and formulas used.
Show complete process. A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 80 mm. Under this load the bar elastically deforms so that the gage length increases to 80.1192 mm and the diameter decreases to 15.89 mm. Determine the modulus of elasticity (in MPa) and Poisson’s ratio for this metal.
A compressive load of 50 KN is applied 150 on the axis of a steel-round bar of 8 mm diameter. Compute its stress and strain if the given modulus of elasticity is 75 GPa. Please draw a figure.
A homogenous steel rod has a diameter of 1.5 inches. When a load is applied, it deformed to about 0.045 inches. If the length of the rod is 6 ft and the modulus of elasticity is E=29x10^6 psi. Determine the force applied in kilopounds (kips).
A steel bar 106mm long and having a square cross section 20 mm (0.8 in.) on an edge is pulled in tension with a load of 89,000 N, and experiencedan elongation of 0.10 mm. Assuming that the deformation is entirely elastic, calculate the elastic modulus of the steel?
A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gauge length of 50 mm. Under this load, the bar elastically deforms so that the gauge length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson’s ratio for this metal.
Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod is 4 m in length. Aluminum has a modulus of elasticity of 69GPa and a Poisson’s ratio of 0.35. 1) What is the decrease in diameter of the rod due to the applied load? 2) What is the new length of the rod?
An aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a compressive load of 50,000 pounds. Assume that the material is within the elastic region and a modulus of elasticity of 11 * 106 psi. a. What will be the lateral strain if Poisson’s ratio is 0.33? b. What will be the diameter after load application? c. What will be the height after load application?
A cylindrical rod with a radius of 0.3 in. and a length of 15 in. is subjected to a tensile load. If the rod is to experience neither plastic deformation nor an elongation of more than 0.018 in. when the applied load is 7,000 lb, which of the four metals or alloys listed below are possible candidates? Justify your choice(s).