A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gauge length of 50 mm. Under this load, the bar elastically deforms so that the gauge length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson’s ratio for this metal.

A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gauge length of 50 mm. Under this load, the bar elastically deforms so that the gauge length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson’s ratio for this metal.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.2P: A tensile test was performed on a metal specimen having a circular cross section with a diameter of...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
A tensile load of 190 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 50 mm. Under this load, the bar elastically deforms so that the gage length increases to 50.1349 mm and the diameter decreases to 15.99 mm. Determine the modulus of elasticity and Poisson’s ratio for this metal.
A homogenous steel rod has a diameter of 1.5 inches. When a load is applied, it deformed to about 0.045 inches. If the length of the rod is 6 ft and the modulus of elasticity is E=29x10^6 psi. Determine the force applied in kilopounds (kips).
A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 80 mm. Under this load the bar elastically deforms so that the gage length increases to 80.1192 mm and the diameter decreases to 15.89 mm. Determine the modulus of elasticity (in MPa) and Poisson’s ratio for this metal.
A tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. by 0.6 in. cross section and a gauge length of 2 in. Under this load, the bar elastically deforms so that the gauge length increases to 2.007 in. and the cross section decreases to 0.599 in. by 0.599 in. Determine the modulus of elasticity and Poisson’s ratio for this metal *
A 10 cm long rectangular bar (when subjected to a tensile load) deforms by 0.1 mm. Calculate the normal strain.
Question 1: A 25mm diameter aluminum rod is loaded axially in tension with a load of 100kN. The rod is 4 m in length. Aluminum has a modulus of elasticity of 69GPa and a Poisson’s ratio of 0.35. 1) What is the decrease in diameter of the rod due to the applied load? 2) What is the new length of the rod?
A tensile load of 50,000 lb is applied to a metal bar with a 0.6 in. * 0.6 in.cross section and a gauge length of 2 in. Under this load, the bar elastically deforms so that the gauge length increases to 2.007 in. and the cross section decreases to 0.599 in. * 0.599 in. Determine the modulus of elasticity and Poisson’s ratio for this metal.
A force of 100,000 N is applied to an iron bar with a cross-sectional area of 10 mm × 20mm and having a yield strength of 400 MPa and a tensile strength of 480 MPa,Determinea. whether the bar will plastically deform; andb. whether the bar will experience necking
A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.4 kN. When the force is increased from 2.4 kN to 9 kN, the specimen elongates 0.250 mm. Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units.
A rod made of aluminum alloy, with a gauge length of 100 mm, diameter of 10 mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.1 mm and the diameter was changed to 9.9967 mm,calculate the modulus of elasticity and Poisson’s ratio.
A rod made of aluminum alloy with a gauge length of 200 mm, diameter of 11mm, and yield strength of 150 MPa, was subjected to a tensile load of 5.85 kN. If the gauge length was changed to 100.10 mm and the diameter was changed to 9.9967mm, calculate the modulus of elasticity and Poison’s ratio. Are the numbers in line with standard numbers for Aluminum Alloy?