While the system shown is in equilibrium, a counter-clockwise torque T = T, sin (wt) N-m (with To =266.1 and w =7.5) is applied to the disk. What is the disk angular speed wm = ở in rad/s at timet = 5.1 sec? T rope viscous friction b I =0.29 kg.m², b =4.6 N-m-s/r, k=1,579 N/m, r =0.34 m.

While the system shown is in equilibrium, a counter-clockwise torque T = T, sin (wt) N-m (with To =266.1 and w =7.5) is applied to the disk. What is the disk angular speed wm = ở in rad/s at timet = 5.1 sec? T rope viscous friction b I =0.29 kg.m², b =4.6 N-m-s/r, k=1,579 N/m, r =0.34 m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 10 N cylinder moves in a friction tube. Spring constants are k1 = 150 N / m and k2 = 200 N / m. When the system is at rest, d = 0.5 m. The system rotates around a fixed z-axis. In the case where d = 0.12 m, what is the coefficient of friction for the cylinder to have a constant velocity of 9.825 m / s?
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
The arms of a Hartnell governor are of equal length. At the mid-position of the sleeve, theball arm is vertical and the radius at which the ball rotates is 10 cm when the equilibriumspeed is 400 RPM. On changing the speed by 1% the governor can overcome the frictionat this position. The friction force is assumed to have a constant value of 20 N at thesleeve. The sleeve moves ± 1.5 cm from the mean position. The minimum speed of thegovernor including friction is 450 rpm. The mass of the sleeve is 3.5 kg. Calculate themagnitude of rotating masses and initial compression of
A uniform circular disk, of 6-kg mass and 0.4-m radius, is placed at the corner, in contact with a vertical wall at A and a horizontal floor at B (Figure 6). A 100-N force is applied to the disk at the top point in the direction as shown in the figure. It is known that the coefficients of static friction between the disk and the wall and the floor are the same. question : Set up three equations of equilibrium at the critical state just about to move, in terms of thenormal forces (NA, NB) and the coefficient of static friction.
Please answer: 3, 4, 5, 6, 8, 9, 10, 12 The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the datum for gravitational potential energy is set as shown below, the the gravitational potential energy of the wheel at the state 1 is 0 N m(two decimal places) (ANSWER IS 0) (2) If the datum for gravitional potential energ is set as shown below, the gravitational potential energy of the wheel at the state 2 is 0 N m (two decimal places) (ANSWER IS 0) (3) At state 1, how long the spring is stretched from its unstretched state (length…
Need help in 15 minutes. ASAP. A 75-kg block is attached to a cable. The cable is then attached to a rotating assembly with a mass moment of inertia of 18 kg-m^2. The bearing friction applied at the rotating assembly equivalent to a couple of 45 N-m CCW. The block's downward speed is initially at 2 m/s. What is the total work done by the system after the rotating assembly has rotated 1.5 radians CW? What is the speed of the 75-kg block after the rotating assembly rotated 1.5 rad CW?
In a porter governor the mass of the central load is 18 kgand the mass of each ball is 2kg. the top arms (250+X) mm while the bottom arms are (300+X) mm long. The friction of the sleeve is 20 N. If the top arms make 45 deg with the axis of rotation in the equilibrium position, find the range of the speed of the governor in that position Note X is the student roll no. for example if the student roll no is A20 then X=20
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
The arms of aHartnell governor are of equal length. At the mid-position of the sleeve, the ball arm isvertical and the radius at which the ball rotates is 10 cm when the equilibrium speed is 400RPM. On changing the speed by 1% the governor can overcome the friction at this position.The friction force is assumed to have a constant value of 20 N at the sleeve. The sleeve moves± 1.5 cm from the mean position. The minimum speed of the governor including friction is450 rpm. The mass of the sleeve is 3.5 kg. Calculate the magnitude of rotating masses andinitial compression of the spring.
The turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.
On a level test track, a car with anti locks brakes and 90% braking efficiency is determined to have a theoretical stopping distance (ignoring aerodynamic resistance) of 408-ft (after the brakes are applied) from 100-mi/h. The car is rear-wheel drive with a 110-inch wheel base, weighs 3200-lb, and has a 50/50 weight distribution (front to back), a center of gravity that is 22-inches above the road surface, an engine that generates 300-ft lb of torque, an overall gear reduction of 8.5 to 1 (in first gear), a wheel radius of 15-inches and a driveline efficiency of 95%. What is the maximum acceleration from rest of this car on this test track? Thank you for helping.
If block A and wedge B have masses. What is the mass of block C if it is on the verge of slipping? All surfaces have a coefficient of static friction of μ. The cable connecting wedge B and block C is parallel with the incline. Use g = 9.806 m/s². Indicate the direction of impending motion for each FBD. μ = 0.15Mass of A = 64kgMass of B = 130 kgα = 22°β = 12°