A 400V, 60HZ, three-phase star-con supplies a delta-connected load, each phase of which has a resistance of 300 and inductance of 40mH If the line resistance is 2.20 between the alternator and load, calculate, ) the current supplied by the alternator (ii) power loss in transmission line (i11) load power factor (iv) power consumed by the load and (v) power supplied by the alternator Ocond device, click on

A 400V, 60HZ, three-phase star-con supplies a delta-connected load, each phase of which has a resistance of 300 and inductance of 40mH If the line resistance is 2.20 between the alternator and load, calculate, ) the current supplied by the alternator (ii) power loss in transmission line (i11) load power factor (iv) power consumed by the load and (v) power supplied by the alternator Ocond device, click on

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Similar questions

A 6,600V, 1,200 kVA, 3-phase alternator is delivering full load at 0.80 power factor lagging. Its reactance is 25% and resistance is negligible. By changing its excitation, the emf is increased by 30%. At this load, determine the new current and power factor. Draw the single line diagram.
a) High Voltages are preferred for Transmission of Electricity. Why? b) Why Generation Voltage Levels are low in the range of 11 kV/ 33 kV etc? c) Why ACSR Conductors are preferred over Copper Conductors? d) Overhead Transmission Lines are preferred for Transmission of Power for Long Distances, why? e) Alternating Current is preferred over Direct Current in Power System, Why? f) Write the Installed Generation Capacity of Sultanate of Oman with current energy share of Conventional and Non-Conventional Energy Sources. g) Why the Capacitance effect is neglected in Short Transmission Line. h) Distinguish between Lumped or Distributed elements in a Transmission Line.
A 100KVA, 220V, a star-connected alternator is loaded at full load and at 60% pf lagging.The effective AC resistance per phase is 0.01411Ω. If the synchronous reactance is 4.5times the effect of the armature leakage reactance wherein the later is 0.046 Ω perphase, find(a) the phase voltage that would be generated at the load if the circuit were operating normally(b) What no-load open-circuit phase voltage must be present in order to circulate full-load current in short-circuit state while maintaining the same speed and field current?(c) What is the terminal phase voltage of the alternator when it is under a shorted load condition? Give an explanation in support of your response using just one sentence. The IA phasor should be used as the reference one.
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…
A transmission line has an actual impedance of 18 ohms, compute for the per unit impedance of this line assume Vbase = 2400, Sbase = 100kVA power factor at unity p.f. round answer to 4 decimal places.
A three-phase, 3-wires CBA System alternator, sending 3-phase voltages of 339.4 volt to the lines, having a delta connected load, with VCA is the reference vector. ZBC = 12.99 – j7.5 ZCA = 8.66 + j5 ZAB = 10 + j0 Determine the phase and line current b) draw the phasor diagram and c) true power generates by the generator neglect the line losses.
(II) If 35 MW of power at 45 kV (rms) arrives at a town froma generator via 4.6Ω transmission lines, calculate (a) theemf at the generator end of the lines, and (b) the fractionof the power generated that is wasted in the lines.
A 3 phase mesh-connected AC generator has a power angle of 15.4 degrees and synchronous impedance of 0.5 + j10 per phase while delivering 300A to its load at a lagging power factor and 13,200 volts line to line. Find the no load emf in volts, line to line.
An electrical motor is supplied from a three-phase ,50 Hz, 410 V system on-board a LNG carrier .When connected in star , it takes a line current of 35 A at a power factor of 0.66 leading. The LNG carrier arrives at port and the motor is subsequently used for powering a container crane It is now connected in delta and is supplied on-shore .Determine for this motor when it takes 64 A at 310 V, from the on-shore supply: 2.1 The power factor of the motor 2.2 the frequency of the supply The motor is returned back to its initial supply and now connected with a new motor in parallel . The new motor is connected in delta and it takes 48.216 kVA at a power factor of 0.77597 lagging with a supply of 50 Hz, 410 V system. Determine for this new arrangement : 2.3 The power factor 2.4 Apparent power taken 2.5 True power taken 2.6 Reactive power taken
A single phase wattmeter is used to determine the power taken by a three phase squirrel cage induction motor. The current coils is placed in line 1 while the potential coil is shifted from lines 1 and 2, then from lines 1 and 3 respectively. If the wattmeter registers 5760 and 3380 watts respectively, what is the line current drawn by the motor. Line to line voltage is 230 V.
The length of a three-phase power transmission line with a nominal operating voltage of 69 kV is 16km. The impedance of the transmission line per unit length is 0.125 + j0.4375 ohm/ km. At the end of the line, a 70 MVA star connected load with a power factor of 0.8 back under 69 kV interphase voltage is fed. Capacitive circuit element with a capacitance of 19.14 mikro F / phase is placed as shunt at the end of the transmission line. According to these given; a) Line head voltage and current, b) Calculate the active and reactive power per line.
The yearly load duration curve of a certain power station can be approximated as a straight line ; the maximum and minimum loads being 80 MW and 40 MW respectively. To meet this load, three turbine generator units, two rated at 20 MW each and one at 10 MW are installed. Determine (i) installed capacity (ii) plant factor (iii) kWh output per year (iv) load factor.