An electrical motor is supplied from a three-phase ,50 Hz, 410 V system on-board a LNG carrier .When connected in star , it takes a line current of 35 A at a power factor of 0.66 leading. The LNG carrier arrives at port and the motor is subsequently used for powering a container crane It is now connected in delta and is supplied on-shore .Determine for this motor when it takes 64 A at 310 V, from the on-shore supply: 2.1 The power factor of the motor 2.2 the frequency of the supply The motor is returned back to its initial supply and now connected with a new motor in parallel . The new motor is connected in delta and it takes 48.216 kVA at a power factor of 0.77597 lagging with a supply of 50 Hz, 410 V system. Determine for this new arrangement : 2.3 The power factor

An electrical motor is supplied from a three-phase ,50 Hz, 410 V system on-board a LNG carrier .When connected in star , it takes a line current of 35 A at a power factor of 0.66 leading. The LNG carrier arrives at port and the motor is subsequently used for powering a container crane It is now connected in delta and is supplied on-shore .Determine for this motor when it takes 64 A at 310 V, from the on-shore supply: 2.1 The power factor of the motor 2.2 the frequency of the supply The motor is returned back to its initial supply and now connected with a new motor in parallel . The new motor is connected in delta and it takes 48.216 kVA at a power factor of 0.77597 lagging with a supply of 50 Hz, 410 V system. Determine for this new arrangement : 2.3 The power factor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.19P

See similar textbooks

Similar questions

A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
Assuming the voltage at the utility bus is 13.5 kV and the PV plant supplies 4.8 MW of power at 0.95 power factor lagging. Draw the diagram of the system and determine i) the per-phase voltage and current at the POI at the PV plant ii) the reactive power delivered and that which is lost in the line. Assume the line is modelled as a short line.
Discuss the significance of power generation, transmission, and distribution in the context of a reliable and efficient power supply. What are the challenges associated with each of these phases?
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the 1/per-unit impedance of the load 2/per-unit current in the line 3/ per-unit real power absorbed by the load
Suppose a power system consists of two isolated regions: a western region and an eastern region. Five units have been committed to supply 3090 MW as shown below. The two systems are separated by a transmission line that can handle a maximum transfer of 550 MW in either direction. Calculate the spinning reserve for the overall system and for eachregion.
50 km of single-phase transmission line, 800 kVA power 8 kV, is carried with 0.9 reverse power factor. The resistance of one kilometer of the line is 42 mΩ, and the reactance of one kilometer of the line is 0.646 Ω. Find the voltage at the beginning of the line and the efficiency of the line accordingly.
1. Write down a formula for the three-phase active power, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements. 2. Write down a formula for the three-phase reactive power, assuming perfectly sinusoidal and symmetrical conditions, using line-line voltage measurements 3. Write down a formula for the three-phase apparent power, assuming perfectly sinusoidal and symmetrical conditions, using line-neutral voltage measurements.
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit impedance of the load. Calculate the per-unit real power absorbed by the load Select one: a. 0.487 b. None of the above c. 0.057 d. 1.253
Discuss the significance of FACTS (Flexible AC Transmission Systems) devices in enhancing power system stability.
A high-voltage power line is made of aluminum conductor steel reinforced (ASCR) material. Suppose a power line has a radius of 2.00 mm and assuming the resistivity of the ACSR is 23.50 x 10^-9 resistor x m, how long is this powerline if it dissipates (on average) 350 MW with a maximum voltage across the powerline of 345,000 Volts (DC)?
Electromechanical energy conversion (One AC induction motor and one AC synchronous motor were operated connected to an infinite bus of 600V. Power factor of the induction motor is 0,7 (lagging) and consumes 400 W from the bus. Synchronous motor consumes 300 W from the bus. If the power factor of the synchronous motor is 0,9 (lagging) find the line current from the bus, for the total of two motors (IL total 1) of the line that connects the motors with the bus and find the total appearent power (SL total 1) of the motors consumed from the bus. When the induction motor has the same conditions, if the power factor of the synchronous motor is 0,9 (leading) find the line current from the bus, for the total of two motors (IL total 2) of the line that connects the motors with the bus and find the total appearent power (SL total 2) of the motors consumed from the bus.
S.1) The serial impedance per phase of a three-phase 45 km energy transmission line is 2 + j4 / phase. A load with a power factor of cos2 = 0.8 forward is fed from the end of the line. Since the line voltage at the beginning and end of the line of the energy transmission line is wanted to be kept constant at 115 kV, a) Active and reactive powers drawn from the beginning and end of the line, b) Calculating the power consumed along the energy transmission line and the efficiency of the line. S.2) Line constants of an energy transmission line are given as A = D = 0.8746 + j0, B = 0 + j128.34, C = j0.0018316 S. At the beginning of the line, it is desired to write 1920 MW active power and 600 MVAr reactive power lines under 7650kV line voltage. According to this business, a) Calculate the line end magnitudes (U2, I2 and P2). b) What value does the end voltage take when the load fed from the end of the line is deactivated? S.3) The length of a phased energy transmission line with a…