A 5-m hollow steel shaft (G= 80 GPa) is subjected to a 25 kN-m torque. The outer diameter is 200 mm. (a) If the total angle of twist must not exceed 3 degrees, the required inner [Select] diameter (in mm) is nearest to? [Select] (b) If the maximum allowable torsional shearing stress is 83 MPa, the require inner radius (in mm) is nearest to?

A 5-m hollow steel shaft (G= 80 GPa) is subjected to a 25 kN-m torque. The outer diameter is 200 mm. (a) If the total angle of twist must not exceed 3 degrees, the required inner [Select] diameter (in mm) is nearest to? [Select] (b) If the maximum allowable torsional shearing stress is 83 MPa, the require inner radius (in mm) is nearest to?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 290 kW(ii) speed = 60 rpm,(iii) Maximum shear stress = 65 MPa(iv) diameter ratio = 1.5(v) The maximum value of the twisting moment is 40% greater than its mean. The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
2-Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. (i) power tranmission = 230 kW(ii) speed = 80 rpm,(iii) Maximum shear stress = 60 MPa(iv) diameter ratio = 1.74(v) The maximum value of the twisting moment is 40% greater than its mean. (i) The mean torque is (Unit is in Nm)=__________ (ii) The maximum torque is (Unit is in Nm)=__________ (iii) The outer diameter of the shaft (unit in mm)=_______________ (iv) The inner diameter of the shaft (unit in mm)=_______________
average shear stress = 50.4 MPa angle of twist per unit length = 3.06 deg/m
Read and Solve carefully please Write clearly and Box the Final answer Express your answer to 3 Significant figures and include appropriate units. QUESTION : Recall that for spings the Zimmerli point on the modified Goodman diagram is located at (Ssm, Ssa) = (55, 35) ksi. Suppose that a particular spring wire has a shear ultimate strength of Ssu = 89 ksi. Determine the shear endurance limit of the spring wire. Give your answer in units of ksi,
Please solve with clear explanation. Q.solid aluminium shaft 1 m long and 50 mm diameter is to be replaced by a tubular steel shaft of the same length and same outside diameter such that each of the two shafts could have the same angle of twist per unit torsional moment over the total length. What must be the inner diameter of the tubular shaft? Modulus of rigidity of steel is three times that of aluminium.
You are a comparative evolutionary biologist that studies biomechanics. In particular, you are interested in how bone cross sectional shapes have evolved. You have discovered a rare (hypothetical) animal that has bone shapes similar to ours, but has solid, rectangular cross sectional areas. You conduct mechanical testing according to the parameters below and want to determine the: (A) moment of inertia; (B) reaction forces and moments at the fixed end O; (C) the stresses at points A, B, and C designated below, including the contributions of the different types of stresses at each point
A windmill turns a series of slender rods fixed about one end (see formula below). They are initially 2 meters long, and go at a speed of 15 rpm. I suggested making the blades 1m long to reduce the cross-sectional area of the windmill, keeping the mass the same for mechanical stress consistency. How fast are the windmill blades going now, in revolutions per minute?
A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1º. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of rigidity is 80 GPa. What is the outside diameter of the shaft?
The rotation or twist in degrees of a shaft, 800 mm long subjected to a torque of 80 N-m, 20 mm in diameter and shear modulus G of 80,000 MPa is:
Topic: Thermal & Torsional Stress The four gears are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20 kW are used by gear A, 20 kW by gear C, and 30 kW by gear D. (a) Find the uniform shaft diameter if the shear stress in the shaft is not to exceed 60 MPa. (b) If a uniform shaft diameter of 100 mm is specified, determine the angle by which one end of the shaft lags behind the other end. Use G = 83 GPa for steel.
Please solve clearly step by step otherwise don't attempt.will report. A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the mean torque. The shear stress in the shaft should not exceed 46 MPa and the twist 1.2° per metre length. Determine the diameter required if, (i) The shaft is solid