A 50-cm x 30-cm x 20-cm block weighing 150 N is to be moved at a constant velocity of 0.8 m/s on inclined surface with a friction coefficient of 0.27. (a) Determine the force F that needs to be applied in the horizontal direction. (b) If a 0.4-mm-thick oil film with a dynamic viscosity of 0.012 Pa.s is applied between the block and inclined surface, determine the percent reduction in the required force. V= 0.8 m/s 50 cm 30 cm 20 150 N

A 50-cm x 30-cm x 20-cm block weighing 150 N is to be moved at a constant velocity of 0.8 m/s on inclined surface with a friction coefficient of 0.27. (a) Determine the force F that needs to be applied in the horizontal direction. (b) If a 0.4-mm-thick oil film with a dynamic viscosity of 0.012 Pa.s is applied between the block and inclined surface, determine the percent reduction in the required force. V= 0.8 m/s 50 cm 30 cm 20 150 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft with a diameter of D = 80 mm and a length of L = 400 mm, shown in Fig is pulled with a constant velocity of U = 5 m/s through a bearing with variable diameter. The clearance between shaft and bearing, which varies from h1 = 1.2 mm to h2 = 0.4 mm, is filled with a Newtonian lubricant whose dynamic viscosity is 0.10 Pa⋅s. Determine the force required to maintain the axial movement of the shaft.
A sleeve of 10cm encases a vertical metal rod 3.0cm in diameter with radial clearance of 0.02mm. if when immersed in oil of viscosity 6.0 poise , the effective weight of the sleeve is 7.5N , will the sleeve slide down the rod and if so, at what velocity?
A shaft 70-mm in diameter is being pushed at a speed of 400mm/s through a bearing sleeve 70.2-mm in diameter and 250mm long. The clearance is filled with oil with a kinematic viscosity of v = 0.005 ?2/? and SG=0.9. Find the frictional resistance exerted by the oil on the shaft in Newtons (N). And when the shaft is fixed axially and rotated inside the sleeve at 2000 rpm, determine the resisting torque exerted by the oil and the power required to rotate the shaft in kiloWatts (kW).
The viscosity of a fluid is to be measured by a viscometer constructed of two 40-cm-long concentric cylinders . The outer diameter of the inner cylinder is 12 cm, and the gap between the two cylinders is 0.15 cm. The inner cylinder is rotated at 300 rpm, and the torque is measured to be 1.8 N⋅m. Determine the viscosity of the fluid.
How would I find an expression for average velocity in a smooth pipe, which is dependant on the viscosity, diameter, and pressure gradient (dp/dx) ?
QUESTION 3A square plate of 0.255 kg mass and 0.5 m side slides down a plane, inclined at anangle of 30° to the horizontal, at a uniform velocity of 0.2 m/s. If the thickness of thefluid film which separates the plate from the plane is 1 200 µm, determine the viscosityof the fluid.
The viscosity of a fluid is to be measured by a viscometer constructed of two 5-ft-long concentric cylinders. The inner diameter of the outer cylinder is 6 in, and the gap between the two cylinders is 0.035 in. The outer cylinder is rotated at 250 rpm, and the torque is measured to be 1.2 lbf⋅ft. Determine the viscosity of the fluid
A thin plate travels between two plane, parallel, horizontal and stationary surfaces at a constant speed of 7 m/s. The two stationary surfaces are spaced 6 cm apart, and the middle is filled with oil of viscosity of 0.9 Ns/m2.The moving plate submerged in oil has a length of 2 m and a width of 0.5 m. (i) If the plate moves through the mid-plane between the surfaces, determine the force required to maintain this motion. (ii) Determine the force if the plate was 1 cm from the bottom surface and 2 cm from the top surface?
The clutch system shown in Fig is used to transmit torque through a 2-mm-thick oil film with ? = 0.38 N⋅s/m2 between two identical 30-cm-diameter disks. When the driving shaft rotates at a speed of 1200 rpm, the driven shaft is observed to rotate at 1125 rpm. Using appropriate software, investigate the effect of oil film thickness on the torque transmitted. Let the film thickness vary from 0.1 mm to 10 mm. Plot your results, and state your conclusions.
The space between the shaft and sleeve is filled with an oil of viscosity 6.5 stokes and density 900 kg/m3. The diameter of the shaft is 45 cm and rotates at the speed of 180 RPM. Determine the thickness of oil film between shaft and sleeve and power lost in bearing if the torque transmitted is 80 N-m and length of the sleeve is 100 mm.
Two identical upright cylindrical tanks contains H2O,the first tank is full and the second is 2/3-full. If theradii of the orifices are the same, compare the time todrain of each tank. answer: √1.5
An 18-kg slab slides down a 15° inclined plane on a 3-mm-thick film of oil with viscosity of 0.0814Pa-sec. If the contact area is 0.3m^3, find the terminal velocity of the slab. Neglect air resistance. ans. 5.614 m/s