5.Determine the power required to run a D- 2N2 cm diameter shaft at N = 8N2 RPM in journals with uniform oil thickness of 0.01N2 mm. Two bearings of L=0.4Nem width are used to support the shaft. The kinematic %3D viscosity of oil is mm/s and density is 28N kg/m? M Shaft 0.01N2 mm 0.4N cm N:27N N2:35 N3:135

5.Determine the power required to run a D- 2N2 cm diameter shaft at N = 8N2 RPM in journals with uniform oil thickness of 0.01N2 mm. Two bearings of L=0.4Nem width are used to support the shaft. The kinematic %3D viscosity of oil is mm/s and density is 28N kg/m? M Shaft 0.01N2 mm 0.4N cm N:27N N2:35 N3:135

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q. 6 A 4.5-cm wide space between two plates is filled with SAE 30W lubricating oil at 26.7°C (Hoil = 0.301645 N.S/m2 ). What is the area of a very thin plate which is dragged by a force of 18 N through the oil at velocity of 16 m/min if the plate is 1.5 cm away from one of the fixed surfaces?
3.A cylindrical shaft of radius 4 cm is rotating at a speed of 30 rad/s in a cylindrical bearing . Shaft and bearing are concentric . The lubricant of viscosity 0,4 Pa s and SG= 0,85 completely fills the clearance between shaft and bearing surface. Take clearance as 0,5 cm and length of shaft as 10 cm . The lubricant flow is laminar steady and uniform .Frictional power loss due to shaft rotation is ?
1. In laminar flow, which is correct?BJ: higher Re value has higher friction factorJB: lower Re value has higher friction factorGroup of answer choices A. BJ is false and JB is true B. BJ is true and JB is false C. BJ is false and JB is false D. BJ is true and JB is true 2.In turbulent flow, which is correct?BJ: higher Re value has lower friction factorJB: lower Re value has higher friction factorGroup of answer choices A.BJ is true and JB is true B.BJ is false and JB is false C. BJ is false and JB is true D. BJ is true and JB is false 3. In a system with 4 reservoirs and 1 pipe junction, how many continuity equations are formulable?Group of answer choices A. 2 B. 3 C. 5 D. 4 E. 1
Determine the NPSH available to avoid the formation of cavitation in the system, water T° 13°C, pipe F°G°, Q=2.45 L/s, Re= 5.4 x 104. The efficiency of the motor will be 0.7, NPSHr = 3mca, the system has an average altitude of 3341 msnm, it is also known that the suction height is 0.80m. Suction pipe diameter 1 ¼”.
fluid mechanics In order to prevent flooding in irrigation areas and to direct the water back to the river or waterbed, the flat cover system given below is preferred. The weight of the cover is 871 kg. The square section cover is hinged 1m above the center of the cover (a = 0.25 m) and b = 1.5 m. The cover has a vertical angle of 40 What should be the maximum water head (h) according to the instructions so that the cover does not open? (psu=1000kg/m3)
1.A cylindrical shaft of radius 5 cm is rotating at a speed of 50 rad/s in a cylindrical bearing . Shaft and bearing are concentric . The lubricant of viscosity 0,6 Pa s and SG= 0,9 completely fills the clearance between shaft and bearing surface. Take clearance as 0,5 cm and length of shaft as 10 cm . The lubricant flow is laminar steady and uniform .The lubricant flow rate in kg/s is ? ANSWER: 1,767 kg/s 2.A cylindrical shaft of radius 5 cm is rotating at a speed of 50 rad/s in a cylindrical bearing . Shaft and bearing are concentric . The lubricant of viscosity 0,6 Pa s and SG= 0,9 completely fills the clearance between shaft and bearing surface. Take clearance as 0,5 cm and length of shaft as 10 cm . The lubricant flow is laminar steady and uniform . Frictional force on shaft surface is ? ANSWER: 9,42 N 3.)A cylindrical shaft of radius 5 cm is rotating at a speed of 50 rad/s in a cylindrical bearing . Shaft and bearing are concentric . The lubricant of viscosity 0,6 Pa s and SG=…
During the test run of a pelton wheel turbine, the pressure of the nozzle was 2.5 mpa when flowing 1.7 m3/s. Penstock inside diameter is 70 cm.Determine the brake power of the pelton wheel if the efficiency is 80%.
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
2. A cylindrical shaft of radius 4 cm is rotating at a speed of 30 rad/s in a cylindrical bearing . Shaft and bearing are concentric . The lubricant of viscosity 0,4 Pa s and SG= 0,85 completely fills the clearance between shaft and bearing surface. Take clearance as 0,5 cm and length of shaft as 10 cm . The lubricant flow is laminar steady and uniform .Frictional force on shaft surface is ?Lütfen birini seçin: a. 4,47 N b. 2,41 N c. 5,53 N d. 9,42 N e. 1,23 N
The runner in a turbine is 70 cm in diameter. The wheel develops 410 kW when turning at 600 rpm under a head of 43 m. What is the specific speed of the turbine? Answer : 28.9 please Explain carefuly
A Pelton turbines is desired to be installed. clear as it is believed to be necessary It can calculate the hydraulic power of turbines with a head of 210 meters relative to each other. Features: do = 120 mmku = 0,42kco = 0,96w2 = 0,85 (C1 – U1)β2 = 160 °
A radial plain bearing has a diameter of 60 mm and a width of 60 mm. Journal rotation speed 600rpm; radial load acting on the bearing is 3.5 kN, the inlet temperature of the SAE 20 oil used is 30 C andSince r / c = 1000;a-) The increase in the temperature of the oil and its average temperature,b-) Minimum oil film thickness, angular position and eccentricity ratio,c-) Loss of power in the bed,d-) Side leaks and total oil flow,e-) Max. oil film pressure.