A 600 MHz NMR has a signal to noise ratio of 1000 for a proton standard. The 400 MHz NMR has a signal to noise ratio of 200 for a proton standard. If it takes 20 minutes to get an acceptable signal to noise ratio for a sample on the 600 MHz NMR, how long will it take you to achieve the same signal to noise ratio on the 400 MHz NMR?

A 600 MHz NMR has a signal to noise ratio of 1000 for a proton standard. The 400 MHz NMR has a signal to noise ratio of 200 for a proton standard. If it takes 20 minutes to get an acceptable signal to noise ratio for a sample on the 600 MHz NMR, how long will it take you to achieve the same signal to noise ratio on the 400 MHz NMR?

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter4: Introduction To Quantum Mechanics

Section: Chapter Questions

Problem 10P: Use the data in Figure 4.8 to estimate the ratio of radiation intensity at 10,000 Å (infrared) to...

See similar textbooks

Similar questions

Use the data in Figure 4.8 to estimate the ratio of radiation intensity at 10,000 Å (infrared) to that at 5000 Å (visible) from a blackbody at 5000 K. How will this ratio change with increasing temperature? Explain how this change occurs.
Given the following data find the Molar absorption coefficient for Fe(SCN)^2+}Fe(SCN)X2+, (M−1 cm−1), if the length is 2.24cm. FIND THE UNROUNDED VALUE. Unrounded Rounded Molar absorption coefficient for \ce{Fe(SCN)^2+}Fe(SCN)X2+, (M−1 cm−1) Sample FROM PRELAB EXPERIMENTAL DATA CALCULATED VALUES 0.000300 M Absorbance Fe(SCN)X2+]equ, (M) --> for next bar 1 1.50 0.210166 0.0000300 2 3.50 0.466178 0.0000700 3 7.00 0.912604 0.000140 4 10.00 1.348948 0.000200 SLOPE, (M−1) INTERCEPT R^2R2 Unrounded 6.66606 × 103 1.20727 × 10-3 0.998979
The following are the reasons why instrumental analysis methods are used, except for: a. Narrow concentration ranges may be detected. b. Extreme low sensitivity, with molecule and noise signal detection. c. Separate equipment or facilities for control, data handling, and optimization procedures. d. All of the above
Below is given the FT-IR (Fourier Transform Infra Red) data of a 1:1 (by weight) mixture of ethylene carbonate (EC) and dimethyl carbonate (DMC). Absorbance Pis given as a function of wavenumber, m. Regress the above data to a second order polynomial P = a, + a, m+ az m? Find the absorbance at m = 1000 cm-1 Wavenumber, m Absorbance, P (arbitrary unit) ( cm-1) 804.184 0.1591 827.326 0.0439 846.611 0.0050 869.753 0.0073 889.038 0.0448 892.895 0.0649 900.609 0.1204
An absorption measurement with a 1 cm path length yields a reading of 0.004 absorbance units with a noise of 0.001 absorbance units and a mean noise reading of 0 for 10 scans averaged together. Assuming the noise for a single scan does not change if the path length is increased to 6 cm and the number of scans is increase to 100, what is the signal to noise of the new measurement.
Potassium dichromate and potassium permanganate have overlapping absorptionspectra in 1M H2SO4 . K2Cr2O7 has an absorption maxima at 440 nm, and KMnO 4 has a band at 545nm (the maximum is actually at 525 nm, but the longer wavelength is generally used whereinterference from K2C2O7 is less). A mixture is analyzed by measuring the absorbance at these twowavelengths with the following results: A 440 =0.405, A 545 =0.712 in a 1-cm cell. The absorbances ofpure solutions of K2Cr2O7 (1x10 -3 M) and KMnO 4 (2.00x10 -4 M) in 1 M H 2 SO 4 , using the same cell gavethe following results: A Cr,440 = 0.374, A Cr,545 = 0.009, A Mn,440 =0.019, A Mn,545 = 0.475. Calculate theconcentrations of dichromate and permanganate in the sample solution.
A 1.2cm diameter glass cuvette is filled with a Cu(NH3)42+ solution that is deep blue. The cuvette is placed into a pre-blanked spectrophotometer. At 620nm, the transmittance is 23%. If the solution has molarity = 0.0133 M and path length of light through the solution = 1.2 cm, what is the value of molar absorptivity at 620 nm?
5.4.5 Chemical microanalysis5.4.5.1 Exploitation of characteristic X-raysElectron probe microanalysis (EPMA) of bulk samples is now a routine technique for obtaining rapid, accurate analysis of alloys. A small electron probe (100 nm diameter) is used to generate X-rays from a defined area of a polished specimen and the intensity of the various characteristic X-rays measured usingeither wavelength-dispersive spectrometers (WDS) or energy-dispersive spectrometers (EDS). Typically the accuracy of the analysis is š0.1%. One of the limitations of EPMA of bulk samples is that the volume of the sample which contributes to the X-ray signal is relatively independent of the size of theelectron probe, because high-angle elastic scattering of electrons within the sample generates X-rays. The consequence of this is that the spatial resolution of EPMA is no better than ¾2 µm. In the last few years EDX detectors have been interfaced totransmission electron microscopes which are capable of operating…
A Dubosq colorimeter consists of a cell of fixed path length and a cell of variable path length. By adjusting the length of the latter until the transmission through the two cells is the same. the concentration of the second solution can be inferred from that of the former. Suppose that a plantdye of concentration 25 μg dm-3 is added to the fixed cell. the length of which is 1.55 em. Then a solution of the same dye. but of unknown concentration. is added to the second cel l. It is found that the same t ransmittance is obtained when the length of the second cel l is adjusted to 1.18 em. What is the concentration of the second solution?
How to find the signal-to-noise ratio from data given? How many measurements would have to be averaged to obtain a S/N of 500? Explanation for each step will be greatly appreciated.
Derive the Scatchard equation for a reaction system 2P + X ↔ P2X, in which only P and P2X have measurable absorbances at the chosen wavelength. Based on this equation and the data given below, determine the values of Keq and ??2? (epsilon P2X). Assume the width of the cuvet used in all of these measurements to be 1cm, i.e., b = 1cm,and the absorbance of the blank solution to be zero. Sample# P0 (M) X0 (M) A 1 4×10-4 0 0.31 2 2×10-4 2×10-2 0.37 3 4×10-4 4×10-2 0.79
Peaks of scattered intensity are observed when the path difference would becomes equal to __________ λ/2 λ 2λ 3λ/2