a) A three-phase star connected alternator supplies a star connected load. Given the supplied single phase voltage Ern = 23020°, and load impedance Zm = Zyn = Zbn = (8 + j12) N. Assumed the system is positive sequence; i. Show all type of voltages and its value at the load on a phasor diagram ii. Calculate the total apparent power, active power, reactive power and overall power factor

a) A three-phase star connected alternator supplies a star connected load. Given the supplied single phase voltage Ern = 23020°, and load impedance Zm = Zyn = Zbn = (8 + j12) N. Assumed the system is positive sequence; i. Show all type of voltages and its value at the load on a phasor diagram ii. Calculate the total apparent power, active power, reactive power and overall power factor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

An unbalanced delta-connected load is supplied from a 400-V, 3-ph, delta-connected alternator through conductors having impedances of 4 + j3 ohms. The load consists of Zab = 15<30 ohms, Zbc=30<45 ohms and Zca = 30<60 ohms. There is no neutral connection. The phase sequence is ABC with Eca as the reference phasor. Determine the line currents and the voltage between the star-point of the alternator and that of the load. Express your answers in polar form.
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. a) Draw the single-phase wye equivalent circuit and label all known parameters numericallyincluding load voltage. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
A 6,600V, 1,200 kVA, 3-phase alternator is delivering full load at 0.80 power factor lagging. Its reactance is 25% and resistance is negligible. By changing its excitation, the emf is increased by 30%. At this load, determine the new current and power factor. Draw the single line diagram.
A 3 phase mesh-connected AC generator has a power angle of 15.4 degrees and synchronous impedance of 0.5 + j10 per phase while delivering 300A to its load at a lagging power factor and 13,200 volts line to line. Find the no load emf in volts, line to line.
A 3 phase, wye-connected salient-pole generator has on per phase basis Xd = 2 ohms, Xq = 1.5 ohms and R∅ = 0. When delivering its maximum power output to an infinite bus bar, the terminal and excitation voltages/phase are 1,430 V and 1,495 V, respectively. Find the power angle in electrical degrees at the above conditions
A 3 phase synchronous generator has a synchronous reactance Xs of 9 Ω perphase, a no-load line to neutral AC voltage E of 12 kV and a line to line terminalvoltage of V of 17.3 kV.(a) Derive the formula for the 3 phase power produced by the generator in terms ofthe power angle δm, |V |, |E|, and Xs. (δm is the angle between E and V ).(b) The power angle δm = 30 degrees. Calculate the 3 phase real power delivered to thegrid at the terminals of the generator.(c) The real power increases when the power angle δm increases, but there is amaximum possible theoretical power that the generator can produce. Calculate themaximum 3 phase real power. Solve A-C
Two 3Ø alternators are supposedly operating in parallel and supplying a total load of11kV, 1500kW at a pf of 0.866 lagging. Initially, one alternator supplies ¼ of the totalpower at 60Hz. The other alternator supplies ¾ of the total power at 59.9Hz. Thesynchronous reactance of each is 50/Ø and the effective AC resistance at 25⁰C is 4/Ø.Without changing any given data, determine the generated voltage of the 2nd alternator
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Consider a 3-phase delta induction motor that is operating at 120 Hz. The motor (load) impedance, Z_Δ is given as (9+j12)Ω. The line-to-line voltage at the load is, ?_ab=416 ∠30ºVrms. Let the source be wye-connected, and line impedance be negligible. b)Determine the rms phase current phasors for each phase. c) Calculate the complex power consumed by the 3-phase load. d) Determine the capacitance value of each capacitor in a 3-phase delta capacitor bank needed to correct the load to a power-factor of 0.9, lagging.
A 15kVA, 440V, single-phase alternator draws a field current of 5A at rated load. With the same field current, the open circuit emf and short-circuit current are 100V and 80A respectively. The ohmic resistance of the armature between terminals is 0.12 ohm. The ratio of effective to ohmic resistance maybe taken as 1.1. Determine the voltage regulation (in %) when the load is purely resistive.
A straight-line law connects terminal voltage and load of a 3-phase star connected alternator delivering current at 0.8 power factor lagging. At no-load, the terminal voltage is 3,500 V and at full-load of 2,280 kW, it is 3,300 V. Calculate the terminal voltage when delivering current to a 3-phase, star-connected load having a resistance of 8 o and a reactance of 6 ohm per phase. Assume constant speed and field excitation.
An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V, has an athree-impedances of 50 / 45 ohms in Delta connection. Assume that Vbc is the reference vector. Determine a) linecurrent and line voltages with its degrees, b)Draw the current –voltage phasor diagram c) and the power generated inthe line quantities of the alternator.