A balanced delta connected load of "17+j18 - per phase is connected at the end of a three-phase line. The line impedance is 7+j9 - per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.

A balanced delta connected load of "17+j18 - per phase is connected at the end of a three-phase line. The line impedance is 7+j9 - per phase. The line is supplied from a three-phase source with a line-to-line voltage of 207.85 Vrms. Taking phase "a" voltage Va as reference, determine the following: (a) Current in phase a. (b) Total complex power supplied from the source. (c) Magnitude of the line-to-line voltage at the load terminal.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter8: Symmetrical Components

Section: Chapter Questions

Problem 8.25P

See similar textbooks

Similar questions

In a balanced three-phase Y-connected system with a positive-sequence source, the line-to-line voltages are 3 times the line-to-neutral voltages and lend by 30. (a) True (b) False
A Y-connected load bank with a three-phase rating of 500 kVA and 2300 V consists of three identical resistors of 10.58. The load bank has the following applied voltages: Vab=184082.8,Vbc=276041.4, and Vca=2300180V. Determine the symmetrical components of (a) the line-to-line voltages Vab0,Vab1, and Vab2, (b) the line-to-neutral voltages and Van0,Van1, and Van2, (c) and the line currents Ia0,Ia1, and Ia2. (Note that the absence of a neutral connection means that zero-sequence currents are not present.)
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
For the power system in Problem 3.41, the synchronous motor absorbs 1500 MW at 0.8 power factor leading with the bus 3 voltage at 18 kV. Determine the bus I and bus 2 voltages in kV Assume that generators I and 2 deliver equal real powers and equal reactive powers. Also assume a balanced three-phase system with positive-sequence sources.
One advantage of balanced three-phase systems over separate singlephase systems is reduced capital and operating costs of transmission and distribution. (a) True (b) False
It is stated that (i) balanced three-phase circuits can be solved in per unit on a per-phase basis after converting - load impedances to equivalent Y impedances. (ii) Base values can be selected either on a per-phase basis or on a three-phase basis. (a) Both statements are true. (b) Neither is true. (c) Only one of the above is true.
The three-phase source line-to-neutral voltages are given by Ean=100,Ebh=10+240, and Ecn=10240volts. Is the source balanced? (a) Yes (b) No
A balanced, star connected three-phase system is directly connected to an unbalanced load, with a solid neutral connection. The line-to-neutral voltage Van on the load side and per phase load impedances (i.e., Za, Zb and Zc) are as below: ?an = 240∠0 ? ?? = 10 + 3? Ω ?? = 16 + 3? Ω ?? = 10 + 3?Ω Draw the circuit diagram and calculate the sequence currents and neutral current
In a three-phase system voltage, assume that the phase-to-neutral voltage at phase “b” is considered as the reference (zero phase angle). 1. State the positive sequence and the negative sequence. 2. Solve the following for both sequences: a. the line-to-neutral voltages : VAN ,VBN and VCN b. the line-to-line voltages : VAB , VBC and VCA
For Figure 1: A short 3-phase line with an impedance of (6+j8) per line has sending end and receiving end line voltages of 120 and 110 kV, respectively. If the power factor at this loading is 0.90 lagging, determine (a) the current delivered to the load, (b) the power consumed by the balanced 3-phase load in kW, and (c) the voltage regulation of the system. (hint: Voltage at the sending and receiving have some magnitude but different angles.)
NOTE :( Just solve only for the Symmetrical components of the corresponding phase voltage) Given the symmetrical components to be V0 = 10<0 V , V1 = 80<30 V , V2 = 40<-30 V determine the unbalanced phase voltages Va, Vb, and Vc.(b) Using the results of part (a), calculate the line-to-line voltages Vab, Vbc, and Vca. Then determine the symmetrical components of these line-to-line voltages, the symmetrical components of the corresponding phase voltages, and the phase voltages.
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…