18.) A 30-km, 34.5 kV, 60 Hz three-phase line has a positive-sequence series impedance z = 0.25 + jo.40 N/km. The load at the receiving end absorbs 50 MVA at 33kV. Determine the following: A.) ABCD Parameters.. B.) Sending-end voltage, current, and power when the load power factor is o.85 lagging; . C.) Sending-end voltage, current, and power when the load power factor is o.8 leading; -

18.) A 30-km, 34.5 kV, 60 Hz three-phase line has a positive-sequence series impedance z = 0.25 + jo.40 N/km. The load at the receiving end absorbs 50 MVA at 33kV. Determine the following: A.) ABCD Parameters.. B.) Sending-end voltage, current, and power when the load power factor is o.85 lagging; . C.) Sending-end voltage, current, and power when the load power factor is o.8 leading; -

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.1P: A 30-km, 34.5-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.19+j0.34/km....

See similar textbooks

Similar questions

Consider a long radial line terminated in its characteristic impedance Zc. Determine the following: (a) V1/I1, known as the driving point impedance. (b) | V2 |/V1|, known as the voltage gain, in terms of al. (c) | I2 |/| I1 |, known as the current gain, in terms of al. (d) The complex power gain, S21/S12, in terms of al. (e) The real power efficiency, (P21/P12)=, terms of al. Note: 1 refers to sending end and 2 refers to receiving end. (S21) is the complex power received at 2; S12 is sent from 1.
A 40-km, 220-kV, 60-Hz, three-phase overhead transmission line has a per-phase resistance of 0.15/km, a per-phase inductance of 1.3263 mH/km, and negligible shunt capacitance. Using the short line model, find the sending-end voltage, voltage regulation, sending-end power, and transmission line efficiency when the line is supplying a three-phase load of (a) 381 MVA at 0.8 power factor lagging and at 220 kV and (b) 381 MVA at 0.8 power factor leading and at 220 kV.
A 200-km, 230-kV, 60-Hz, three-phase line has a positive-sequence series impedance z=0.08+j0.48/km and a positive-sequence shunt admittance y=j3.33106S/km. At full load, the line delivers 250 MW at 0.99 p.f. lagging and at 220 k V. Using the nominal circuit, calculate: (a) the ABCD parameters, (b) the sending-end voltage and current, and (c) the percent voltage regulation.
The 500-kV, 60-Hz, three-phase line in Problems 4.20 and 4.41 has a 180-km length and delivers 1600 M W at 475 kv and at 0.95 power factor leading to the receiving end at full load. Using the nominal circuit, calculate the (a) ABCD parameters, (b) sending-end voltage and current, (c) sending-end power and power factor, (d) full-load line losses and efficiency, and (e) percent voltage regulation. Assume a 50C. conductor temperature to determine the resistance of this line.
Question 1. The impedance of a 150 km long transmission line is ? = 0.06 + ?0.48 ?/??, and the shunt admittance value is given as ? = ?3.33?10−6 ?/??. Under 250 kV voltage at the end of the line A power of 250 MW is drawn with a reverse power factor cos ? = 0.95. Nominal π equivalent using the circuit; a) Find the ABCD parameters. b) Find the voltage, current and power factor per line.
A single circuit 60 Hz transmission line. the conductors are Linnet type with flat horizontal spacing of 17.46 feet between conductors. Determine: (a) Assume that the line is short with a length of 50 miles, calculate the parameters of the line and draw the equivalent circuit. (b) Assume that the line is average with length of 150 miles (Pi-nominal model). draw the pi-nominal circuit for the transmission line and calculate its parameters (Z and Y/2 values, where Z is the series impedance of the transmission line and Y is the shunt admittance).
2. A 200-km, 230-kV, 60-Hz three-phase line has a positive-sequence series impedance z = 0.07 + j0.58 ohms/km and a positive-sequence shunt admittance y = j4.33 x 10^-6 S/ km. At full load, the line delivers 350 MW at 0.95 pf lagging and at 220 kV. Using the nominal pi circuit, calculate: (a) the ABCD parameters (b) the sending-end voltage and current, and (c) the percent voltage regulation.
a) Find the IBC load current.b) Give the Vca line voltage.c) Calculate the total complex power on the transmission line.
A 69-kV, three phase short transmission line is 16km long. The line has a per phase series impedance of 0.125 + j0.4375 ohms per km. Determine the sending end voltage, voltage regulation, the sending end power, and the transmission efficiency when the line delivers:(a) 70 MVA, 0.8 lagging power factor at 64 kV.(b) 120 MW, unity power factor at 64kV.
In three-phase short transmission line with end-of-line interphase voltage UR = 31,5kV , from the end of the line active power absorbed PR = 9000 kW, end of line power factor is cosφ = 0,70 (end) and the length of the line is l = 20km, The resistance of the line per km is R'= 0,125 Ohm/km, the reactance per km is X'= 0,375 Ohm/km.With the help of given information; a) Calculate the current drawn from the line (IR) as a phasor. b) Calculate the line-to-line-neutral voltage (VS) as a phasor, determine the effective line-to-line voltage (US) Calculate its value. c) Calculate the line head power factor, active and reactive power drawn from the line head, d) Draw the phasor diagram of the system. ..
b) Ghana Grid Company (GRIDCo) designed a short transmission line using the A, B, C, D line constant of a transmission line parameters in its analysis. The engineering planning department came up with the design and said that when they computed the line performance using the equation AD – BC the answer was equal to 1.As an employee at the Ministry of Energy (MoEn) having oversight responsibility over GRIDCo, how would you accept the answer and recommend the Government of Ghana (GoG) to go ahead to implement the short transmission line?
A conventional nominal T transmission line is composed of the following: a lumped shunt (parallel) impedance of 92 ohms at the center of the line and a lumped sending and receiving series impedance of 496 ohms for both ends. In a two-port network analysis, determine the Z12 parameter of the circuit described.