A beam is a structural member that is subjected primarily to transverse loads. The beam AB in Figure 2 is a cantilever beam with fixed-end support at A. The beam is subjected to a moment couple Mo acting at B. Demonstrate formulas for the angle of rotation Og and the deflection 8p at end B. The beams have constant flexural rigidity EI. IA B Мо L Figure 2

A beam is a structural member that is subjected primarily to transverse loads. The beam AB in Figure 2 is a cantilever beam with fixed-end support at A. The beam is subjected to a moment couple Mo acting at B. Demonstrate formulas for the angle of rotation Og and the deflection 8p at end B. The beams have constant flexural rigidity EI. IA B Мо L Figure 2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.3.10P: A cantilever beam model is often used to represent micro-clectrical-mechanical systems (MEMS) (sec...

See similar textbooks

Similar questions

A fixed-end beam AB carries point load P acting at point C. The beam has a rectangular cross section (b = 75 mm, h = 150 mm). Calculate the reactions of the beam and the displacement at point C. Assume that E = 190 GPa.
The wing of a small plane is represented by a simplified prismatic cantilever beam model acted on by the distributed loads shown in the figure. Assume constant El = 1200kN-m~, Find the tip deflection and rotation at B.
-20 Derive the equations of the deflection curve for a cantilever beam AB carrying a uniform load of intensity q over part of the span (see figure). Also, determine the deflection Bat the end of the beam. Use the second-order differential equation of the deflection curve.
The compound beam shown in the figure consists of a cantilever beam AB (length L) that is pin-connected to a simple beam BD (length 2L). After the beam is constructed, a clearance c exists between the beam and a support at C, midway between points B and ZX Subsequently, a uniform load is placed along the entire length of the beam. What intensity q of the load is needed to close the gap at C and bring the beam into contact with the support?
A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A linearly varying distributed load with peak intensity q0acts on the beam, (a) Find peak intensity q0if the deflection at joint B is known to be 0.18 in. Assume that modulus E = 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.
Obtain a formula for the ratio c/maxof the deflection at the midpoint to the maximum deflection for a simple beam supporting a concentrated load P (see figure). From the formula, plot a graph of c/max versus the ratio a/L that defines the position of the load (0.5 < a/L < ) What conclusion do you draw from the graph? (Use the formulas of Example 9-3.)
-12 Determine the angle of rotation Band deflection Bat the free end of a cantilever beam AB having a uniform load of intensity q acting over the middle third of its length (see figure).
A simple beam ABC has a moment of inertia 1,5 from A to B and A from B to C (see figure). A concentrated load P acts at point B. Obtain the equations of the deflection curves for both parts of the beam. From the equations, determine the angles of rotation 0Aand Bcat the supports and the deflection 6Bat point B.
-21 Derive the equations of the deflection curve for a cantilever beam AB supporting a distributed load of peak intensity q0acting over one-half of the length (see figure). Also, obtain formulas for the deflections Band cat points B and C, respectively Use the second-order differentia] equation of the deflection curve.
-19 Derive the equations of the deflect ion curve for a simple beam AB loaded by a couple M0acting at distance a from the left-hand support (see figure). Also, determine the deflection B at the point where the load is applied. Use the second-order differential equation of the deflection curve.
The figure shows a nonprismatic, propped cantilever beam AB with flexural rigidity 2EI from A to C and EI from C to B. Determine all reactions of the beam due to the uniform load of intensity q. Hint: Use the results of Problems 9.7-1 and 9.7-2.
A simply supported beam (E = 1600 ksi) is loaded by a triangular distributed load from A to C(see figure). The load has a peak intensity q0= 10 lb/ ft, and the deflection is known to be 0.01 in, at point C. The length of the beam is 12 ft, and the ratio of the height to the width of the cross section is (h:b) 2:1, Find the height h; and width h of the cross section of the beam.