The cantilever beam consists of a rectangular structural steel tube shape [E = 27000 ksi; / = 450 in.4]. For the loading shown, determine: (a) the beam deflection vg at point B. (b) the beam deflection vc at point C. Assume P = 10.9 kips, w = 2.9 kips/ft, LAB= 7.6 ft, LBC = 4.6 ft. "I W ↓↓ B LAB in. A Answers: (a) vg= -0.6016 (b) vc= i -1.2143 in. LBC

The cantilever beam consists of a rectangular structural steel tube shape [E = 27000 ksi; / = 450 in.4]. For the loading shown, determine: (a) the beam deflection vg at point B. (b) the beam deflection vc at point C. Assume P = 10.9 kips, w = 2.9 kips/ft, LAB= 7.6 ft, LBC = 4.6 ft. "I W ↓↓ B LAB in. A Answers: (a) vg= -0.6016 (b) vc= i -1.2143 in. LBC

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.5.5P: A cantilever beam of a length L = 2.5 ft has a rectangular cross section {b = 4in,, h = Sin,) and...

See similar textbooks

Similar questions

.2 A ligmio.irc ii supported by two vorlical beams consistins: of thin-walled, tapered circular lubes (see ligure part at. for purposes of this analysis, each beam may be represented as a cantilever AB of length L = 8.0 m subjected to a lateral load P = 2.4 kN at the free end. The tubes have a constant thickness ; = 10.0 mm and average diameters dA = 90 mm and dB = 270 mm at ends A and B, re s pec lively. Because the thickness is small compared to the diameters, the moment of inerlia at any cross section may be obtained from the formula / = jrrf3;/8 (see Case 22, Appendix E); therefore, the section modulus mav be obtained from the formula S = trdhlA. (a) At what dislance A from the free end docs the maximum bending stress occur? What is the magnitude trllul of the maximum bending stress? What is the ratio of the maximum stress to the largest stress (b) Repeat part (a) if concentrated load P is applied upward at A and downward uniform load q {-x) = 2PIL is applied over the entire beam as shown in the figure part b What is the ratio of the maximum stress to the stress at the location of maximum moment?
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
A simple beam AB of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection S at the midpoint of the span (see figure). How much strain energy U is stored in the beam if the deflection curve is (a) a parabola and (b) a half wave of a sine curve?
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
A simple beam AB of length L and height h (see figure) is heated in such a manner that the temperature difference 7= T{between the bottom and top of the beam is proportional to the distance from support A: that is, assume the temperature difference varies linearly along the beam: T2- Tt= Tax in which 7"0 is a constant having units of temperature (degrees) per unit distance. Determine the maximum deflection SW9Xof the beam, Repeat for a quadratic temperature variation along the beam, so T2+T1= Tax
A cantilever beam with length l is carrying a uniformly distributed load, w. What is the maximum deflection of the beam, in millimeters? w = 7 kN/m l = 6.7 m EI = 60000 kNm2
Solve for the deflection of a simply supported beam (b = 60 mm, h = 125 mm, length = 3 m, E = 10 GPa) at x = 1.5 m, with a positive (upwards pointing) uniform distributed load running the whole length of the beam. Also, solve for the slope at x = 1.5 m.
The cross section of a rectangular beam having wodht b and height h is shown in part a of a figure 1. For reasons unknown to the beam designer, it is planned to add structural projections of width b/9 and height d to the top and the bottom of the beam(see part b of figure 1)For what values of d is the section modulus S of the beam increased?For what values is it decreased?Hint: Express the section modulus S of the modified section as function of d.then divide S by the section modulus of the orignal section,and plot the result as a function of d/h. The plot will indicate for which values od d, in reference to h, the new section modulus is increased/decreased.
Since the load state and the rectangular cross section of the horizontal beam element are 200 MPa, the shear stress value is 200 MPa;What is the safety beam section (bx2b) value?
For the beam and loading shown below, determine the beam deflection at point H. Assume that EI = 5.7 × 104 kN·m2 is constant for the beam; w = 8.1 kN/m, LHA = 2.7 m, LAB = 5.4 m.
From the given beam loaded as shown, Let P = 12 kips, L = 7 ft, a = 3 ft. E = 29 x 10^6 psi, I = 722 in^4. a. Equation of the slope b. Equation of the deflection curve c. The deflection at the midpoint. d. The slope at point B.
Total beam depth, H = 759 mm Web thickness, tw = 19 mm Flange width, B = 354 mm Flange thickness, tf = 32 mm What is The moment of inertia Ix about the principal axis?