A) Calculate the deflection and rotation at point (c) for the beam showing in figure by using unit load method. (E 200*106 kN/m2, I = 3.125*103 m*). 9 kN/m a 3 m 3 m

A) Calculate the deflection and rotation at point (c) for the beam showing in figure by using unit load method. (E 200106 kN/m2, I = 3.125103 m*). 9 kN/m a 3 m 3 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.6.5P: -5 Calen1ate the deflections S 3a nd

See similar textbooks

Related questions

Q: Problem 10: For the given beam find maximum slope and maximum deflection. Also find slop and…

Q: An I-profile steel beam is supported and loaded as shown in the figure. If the mass of the block is…

A: E=200 GPa,I=17×106 mm4L=8 m or 8000 mmb=2000mmFor simply supported beam, deflection y is given…

Q: Figure shown below is a beam with loading, determine the following: (a) Equation of the elastic…

Q: Homework; In Figure below, a cantilever beam is subjected to an inclined force (P); calculate: 1-…

Q: . Figure shows a simply supported beam of span 5m carrying two point loads. Find a). The deflection…

Q: 4 kN A 30 6 m -2 m

Q: Calculate the maximum shear stress Tmax and the maximum bending stress σmax in a simply supported…

A: Given data: The uniform load on the beam, w = 18 kN/m. The length of the beam, l = 1.75 m. The…

Q: a. Show that the best material for a cantilever beam of given length L and given (i.e., fixed)…

Q: A simply supported beam of length 5m, with a hollow rectangular cross-section outer width of 45mm x…

Q: A simply supported beam hinged at A and supported at C, is carrying a distributed load and a point…

Q: 2 Find the equation of deflection (under the uniformly distributed load) and calculate the maximum…

Q: (b) Using Macaulay's method, calculate the deflection at the middle of the beam shown in Figure 1b.…

A: Given data To determine the deflection at the middle of the span AB

Q: / The simply supported beam shown in Figure below has a central half of the beam enlarged, so that…

Q: If w = 25 kN/m., calculate the value of EIδ at 1 m. of the free end of the loaded beam as indicated…

Q: Find the slope deflections using any unit load method in the text book. For the beam shown in figure…

Q: ire Q3. AB is 2 m, BC is 2 m and CD is 1 m in lengths. By using Macaulay's hod, calculate the:…

Q: Find the slope deflections using unit load method or any other method in the text book. For the beam…

Q: Analyze the given structure and find out the slope teta at point B of the steel beam .Take E=200 GPa…

A: E=200 GPa = 200*109 Pa I=60 x106 mm4=60*106*10-12m4=60*10-6m4 AB=8m BC=15m W=2kN=2*103 N

Q: Figure below shows a beam acted upon a triangular distributed load. What is the magnitude and…

Q: Find the slope deflections using any unit load method in the text book. For the beam shown in figure…

Q: Figure Q5 (a) shows a wood beam reinforced with steel straps at its top and bottom. If the beam is…

A: Given Cross-section is:

Q: Find the slope deflections using unit load method or any other method in the text book. For the beam…

A: The deviation is the level at which a structural element is moved under the load (due to its…

Q: Find slope and deflection in beam at point C shown in figure below. Assume that modulus of…

A: Let :-∑Fy =…

Q: Find the deflection at load F by Castigliano's Theorem in a bow and arrow. Draw a Free-body diagram…

A: Draw a free body diagram.

Q: A cantilever beam of rectangular cross- section is subjected to load at free end. If the depth of…

Q: Problem 9: Find the Slope and deflection at B and C for a cantilever beam of L subjected to a load…

Q: A 1m span beam carrying UDL of 384N/m whose is maximum deflection at centre 5/EI -5/EI 7/EI…

Q: QUESTION 3 Calculate the vertical deflection at point 'A' for the thin curved beam shown in figure…

Q: 9.5-2 A simply supported beam (E = 12 GPa) car- Tics a uniformly distributed load q = 125 N/m, and a…

A: Find the maximum deflection of the beam.

Q: A cantilever beam AB of length Land uniform flexural rigidity El has a bracket AC attached to its…

Q: 20kN/m 20kN/m 1m 2m 1m 1m 5m

A: Given: Total length of a cantilever beam, l =5 m Beam is subjected to two uniformly distributed…

Q: 9.6-5 Calculate the deflections &g and &e at points B and C, respectively, of the cantilever beam…

A: Given, Mo=36kip-inP=3.8kipsL=8ft=96inchEI=2.25×109lb-in2EI=2250000kip-in2 Deflection at point B,…

Q: For figure Task 2b find the slope and deflection at the free end of the cantilever beam. Take…

A: L = 2.5 m To find: (a) Slope at the free end. (b) Deflection at the free end.

Q: 9.5-2 A simply supported beam (E = 12 GPa) car- THes a uniformly distributed load q point load P =…

Q: Q 2. Calculate the slope and deflection at the free end of the cantilever beam shown in figure using…

A: Given, young's modulus , E = 2.05 *105 N/mm2. Let the last two digits of student id be 51 , I =…

Q: A simply supported beam is loaded with apoint load, as shown in the figure. The beam is a steelwide…

A: Given data as per question P = 10 kips f L =10 ft a = 7 ft b = 3 ft

Q: A 356 x 171 US45 steel beam is supported at ends of a span of 5.5m. The beam carries a safe…

A: The span of the beam is L=5.5 m =5.5 m×1000 mmm=5.5×103 mm. The value of UDL is w= 12 kN/m=12…

Q: A cantilever beam with flexural regidity of 200 N/m2 is loaded as shown in figure. Find the…

A: Given:Rigidity, EI=200 N/m2W=500 Nx=50 mm= 0.5mTo find:-Deflection at tip of the beam

Q: Calculate the deflection and rotation at point (a) for the beam showing in figure by using unit load…

A: Deflection If the beam undergoes some load on it then deformation in the beam takes place and this…

Q: Q2. Calculate the slope and deflection of a SSB with span 5m carrying a point load of 20kN at 2m…

A: Given Data, There is a simply supported beam. L = Length of the beam = 5 m E = Young's Modulus of…

Q: b) A simply supported beam of span 20m carries two concentrated loads 4kN at 8m and 10kN at 12m from…

Q: Mo Мо А В X+ L

A: A beam is defined as a structural member subjected to transverse shear load during its…

Q: Q4: For the simply surported beam loaded as in the figure. " 10 kN/m 1. Find the beam deflection…

Q: n curve at th

Q: Q2: Find the deflection Equation of Simply Supported Beams Subjected to the triangular distributed…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A) Calculate the deflection and rotation at point (c) for the beam showing in
figure by using unit load method. (E = 200*106 kN/m?, I = 3.125*103 m*).
9 kN/m
a
C
3 m
3 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.
-5 Calen1ate the deflections S 3a nd
A simple beam AB of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection S at the midpoint of the span (see figure). How much strain energy U is stored in the beam if the deflection curve is (a) a parabola and (b) a half wave of a sine curve?
A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
Obtain a formula for the ratio c/maxof the deflection at the midpoint to the maximum deflection for a simple beam supporting a concentrated load P (see figure). From the formula, plot a graph of c/max versus the ratio a/L that defines the position of the load (0.5 < a/L < ) What conclusion do you draw from the graph? (Use the formulas of Example 9-3.)
A propped cantilever steel beam is constructed from a W12 × 35 section. The beam is loaded by its self-weight with intensity q. The length of the beam is 1L5 ft. Let E = 30,000 ksi. Calculate the reactions at joints A and B. Find the location of zero moment within span AB. Calculate the maximum deflection of the beam and the rotation at joint B.
A cantilever beam JA of length Land height/; (see figure) is subjected to a temperature change such that the temperature at the top is 7[ and at the bottom is 7. Determine the equation of the deflection curve of the beam, the angle of rotation BBat end and the deflection 8Bat end B,
A cantilever beam has a length L = 12 ft and a rectangular cross section (b = 16 in., h = 24 in.), A linearly varying distributed load with peak intensity q0acts on the beam, (a) Find peak intensity q0if the deflection at joint B is known to be 0.18 in. Assume that modulus E = 30,000 ksi. (b) Find the location and magnitude of the maximum rotation of the beam.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
Obtain formulas for the angle of rotation 0Aat support A and the deflection SajAXat the midpoint for a simple beam AB with a uniform load of intensity q (see figure).
A two-axle carriage that is part of an over head traveling crane in a testing laboratory moves slowly across a simple beam AB (sec figure). The load transmitted to the beam from the front axle is 2200 lb and from the rear axle is 3800 lb. The weight of the beam itself may be disregarded. Determine the minimum required section modulus S for the beam if the allowable bending stress is 17,0 ksi, the length of the beam is 18 ft, and the wheelbase of the carriage is 5 ft. Select the most economical I-beam (S shape) from Table F-2(a), Appendix F.