A binary counter that will count 0 to 5 is wanted to be designed. A floating light line including 6 lights will be controlled by this counter. At each clock pulse, 3 lights will be ON, 3 lights will be OFF. Design the circuit by using JK flip flops and ROM. Hint: Assume that all the lights are in OFF position before beginning. Lights will look like when the clock pulses are started to come: On on on off off off Off on on on off off

A binary counter that will count 0 to 5 is wanted to be designed. A floating light line including 6 lights will be controlled by this counter. At each clock pulse, 3 lights will be ON, 3 lights will be OFF. Design the circuit by using JK flip flops and ROM. Hint: Assume that all the lights are in OFF position before beginning. Lights will look like when the clock pulses are started to come: On on on off off off Off on on on off off

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a synchronous BCD Counter based on the following conditions. If last digit of your roll number is odd then design down-counter with JK-Flip Flops by initializing the counter with last digit and count next five states. The counter should cycle back after counting five states. Hint: roll number = 169
Design a binary counter that counts from 0 to 5. At each clock pulse, 3 lights will be ON and 3 lights will be OFF. Use JK flip flops.Steps for solution:-> State diagram-> State table-> K-map reductions-> design
You are asked to design a synchronous counter that will count the sequence 1 > 2>3>1. (a) Represent these decimal numbers in 2 bits binary numbers. (b) Write down the state table. (c) Find the functions for the next state of the state table using K-map. (d) Draw the circuit (You need to consider D flip-flops as memory unit).
Implement a 4-bit synchronous up counter with positive edge triggered D flip flops by doing thefollowing. Up counter means counting from 0000, 0001, 0010, ... to 1111, then 0000, 0001, ....1) Derive a state table for this counter with D flip flop.2) Develop state input equations.3) Sketch a logic diagram for this counte
about 4 bit Synchronous Up/Down Counter using JK flip flops and explain how it functions, find real life applications.
Note: the value of each flip-flop, before the first clock pulse, is “0” so initially the state of the three flip-flops is Q2=0; Q1=0 and Q0= 0 (i) What is the function of this circuit? (ii) Find the sequence of states generated after each of the first 9 clock pulses (iii) Determine the waveform after each clock pulse until the 9th pulse
Digital Circuit Design Design a reverse counter with three D flip‐flops A, B and C. The counter counts from 7, 6, ..., 0, then to 7, and continues. the answer has to include : circuit diagram state equations state table state diagram
(i) Determine how many flip flops are required to build a binary counter that count from 0 to 1023?(ii) Determine the frequency at the output of the last flip flop of this counter for an input clock frequency of 2 MHz.(iii) Give the MOD number of this counter.(iv) If the counter is initially at zero, determine the count if it hold after 2060 pulses.
Question 5(a) ) (i)What is a flip-flop? What is the difference between a latch and a flip-flop? List out the applications of flip-flop (ii) In a JK Flip-Flop, what is the meaning of toggle, and how does it happen (b) Kindly design a Master-slave J-K flip-flop using NAND gates only and state race-around condition, and how it can be eliminated in a Master-slave J-K flip-flop? (c) In your own understanding kindly demonstrate why in digital logic family, ECL has the lowest propagation delay time?
We wish to design a digital system with two flip-flops, say B and C, and one 4-bit binarycounter A, in which the individual flip-flops are denoted by A4, A3, A2, A1. A start signal Sinitiates the system operation by clearing the counter A and flip-flop C, and settling flip-flop B toone. The counter is then incremented by one starting from the next clock pulse and continues toincrement until the operations stop. Counter bits A3 and A4 determine the sequence ofoperations:If A3 = 0, B is cleared to 0 and the count continues.If A3 = 1, B is set to 1; then if A4 = 0, the count continues, but if A4= 1, C is set to 1 on the nextclock pulse and the system stops counting.Then if S = 0, the system remains in the initial state, but if S = 1, the operation cycle repeats.(a) Draw the ASM Chart(b) Draw the equivalent one flip-flop per state
Design SYNCHRONOUS COUNTER using J-K flip flops that counts downfrom 9 to 0.-Show the state and excitation tables for the counter. -Express the flip-flop input functions as a minimal SOP expressions.-. Draw the logic diagram for the counter.
Draw and explain the operation in detail (while including necessary table) the block diagram and logic circuit diagram of J-K master-slave (M-S) flip flop. Why an M-S configuration is necessary?