A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Show fbd and solution a. 0.636 b. 0.629 c. 0.989 d. 0.98

A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Show fbd and solution a. 0.636 b. 0.629 c. 0.989 d. 0.98

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc. 0.629 0.989 0.636 0.98
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd, Cc, and Cv, Show a Diagram
A calibration test of a 2.5cm circular sharp-edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measurement of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc. Answers: a.0.636 b.0.989 c.0.629 d.0.98
A calibration test of a 12.7mm circular sharp edge orifice in the vertical side of a large tank showed a discharge of 589N of water in 81 sec. at a head of 4.73. Measurement of the jet showed that it traveled 2.35m horizontally while dropping 0.0305m. Compute the three orifice coefficients.
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7.89cm radius?
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7cm by 5cm dimension.
HYDROSTATIC FORCE ON PLANE SURFACE can someone help me analyze this experiment? For fully submerged: - compare the results of W x r with the calculated values of F x (Xcp + hs). - give reasons for discrepancies. - what can you obtain from the relationship of the graph? Does the experiment confirm the results of computed values of the magnitude and location of the total hydrostatic force?
for a sample of water ec reading was called 178 X 10^-3 siemens per centimeter calculate the value of tds in ppt
A permeability test was carried out from a well that sunk through a surfacelayer of loose sand. Figure below shows the arrangement of pumping wells, togetherwith relevant dimensions. Initially, the piezometric surface (ground water table) waslocated at a depth of 2.5m. When steady state was achieved at a pumping rate 38.5 m^3/hr, the following drawdowns were observed. Pumping well, d0 = 3.64mObservation well, d1=0.96mObservation well, d2 = 0.48m Calculate the coefficient of permeability of the sand in m/hr
24/27/30 After conducting a fall cone test, the regression equations obtained from the 80g and 240g cones were w=38.2log(d)+13.1 and w=38.2log(d)+2.3, respectively. Determine the liquid limit and plastic limit.Determine Δw. Note: w (%) is the moisture content and d (mm) is the depth of penetration.
In Hydrometer test, we commonly do a few corrections to the readings we take off the Hydrometer stem.First, discuss why we need these corrections. Second, list and discuss the common corrections we make duringa Hydrometer reading
Write the expression for correction due to dilatancy submergence?