A catalytic converter in an automobile uses a palladium or platinum catalyst to convert carbon monoxide gas to carbon dioxide according to the following reaction: 2C0(g) + O2(9) → 2CO2(9) A chemist researching the effectiveness of a new catalyst combines a 2.0:1.0 mole ratio mixture of carbon monoxide and oxygen gas (respectively) over the catalyst in a 2.45- L flask at a total pressure of 735 torr and a temperature of 552 C. When the reaction is complete, the pressure in the flask has dropped to 554 torr. Part A What percentage of the carbon monoxide was converted to carbon diaxide?

A catalytic converter in an automobile uses a palladium or platinum catalyst to convert carbon monoxide gas to carbon dioxide according to the following reaction: 2C0(g) + O2(9) → 2CO2(9) A chemist researching the effectiveness of a new catalyst combines a 2.0:1.0 mole ratio mixture of carbon monoxide and oxygen gas (respectively) over the catalyst in a 2.45- L flask at a total pressure of 735 torr and a temperature of 552 C. When the reaction is complete, the pressure in the flask has dropped to 554 torr. Part A What percentage of the carbon monoxide was converted to carbon diaxide?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter5: Gases

Section: Chapter Questions

Problem 162CP

See similar textbooks

Similar questions

105 The decomposition of mercury(II) thiocyanate produces an odd brown snake-like mass that is so unusual the process was once used in fireworks displays. There are actually several reactions that take place when the solid Hg(SCN)2 is ignited: 2Hg(SCN)2(s)2HgS(s)+CS2(s)+C3N4(s)CS2(s)+3O2(g)CO2(g)+2SO2(g)2C3N4(s)3(CN)2(g)+N2(g)HgS(s)+O2(g)Hg(l)+SO2(g) A 42.4-g sample of Hg(SCN)2 is placed into a 2.4-L vessel at 21°C. The vessel also contains air at a pressure of 758 torr. The container is sealed and the mixture is ignited, causing the reaction sequence above to occur. Once the reaction is complete, the container is cooled back to the original temperature of 21°C. (a) Without doing numerical calculations, predict whether the final pressure in the vessel will be greater than, less than, or equal to the initial pressure. Explain your answer. (b) Calculate the final pressure and compare your result with your prediction. (Assume that the mole fraction of O2 in air is 0.21.)
93 The complete combustion of octane can be used as a model for the burning of gasoline: 2C8H18+25O216CO2+18H2O Assuming that this equation provides a reasonable model of the actual combustion process, what volume of air at 1.0 atm and 25°C must be taken into an engine to burn 1 gallon of gasoline? (The partial pressure of oxygen in air is 0.21 atm and the density of liquid octane is 0.70 g/mL.)
84 Consider a sample of an ideal gas with n and T held constant. Which of the graphs below represents the proper relationship between P and V? How would the graph differ for a sample with a larger number of moles?
When two cotton plugs. one moistened with ammonia and the other with hydrochloric acid, are simultaneously inserted into opposite ends of a glass tube that is 87.0 cm long, a white 1111g of NH4Cl forms where gaseous NH3 and gaseous HC1 first come into contact. NH3(g)+HCl(g)NH4Cl(s) At approximately what distance from the ammonia moistened plug does this occur? (Hint: Calculate the rates of diffusion for both NH3 and HCI, and find out how much faster NH3 diffuses than HCI.)
97 Homes in rural areas where natural gas service is not available often rely on propane to fuel kitchen ranges. The propane is stored as a liquid, and the gas to be burned is produced as the liquid evaporates. Suppose an architect has hired you to consult on the choice of a propane tank for such a new home. The propane gas consumed in 1.0 hour by a typical range burner at high power would occupy roughly 165 L at 25°C and 1.0 atm, and the range chosen by the client will have six burners. If the tank under consideration holds 500.0 gallons of liquid propane, what is the minimum number of hours it would take for the range to consume an entire tankful of propane? The density of liquid propane is 0.5077 kg/L.
In a typical automobile engine, a gasoline vapor-air mixture is compressed and ignited in the cylinders of the engine. This results in a combustion reaction that produces mainly carbon dioxide and water vapor. For simplicity, assume that the fuel is C8H18 and has a density of 0.760 g/mL. (a) Calculate the partial pressures of N2 and 02 in the air before it goes into the cylinder; assume the atmospheric pressure is 734 mmHg. (b) Consider the case where the air, without any fuel added, is compressed in the cylinder to seven times atmospheric pressure, the compression ratio of many modem automobile engines. Calculate the partial pressures of N2 and O2 at this pressure. (c) Now consider the case where 0.050 mL gasoline is added to the air in the cylinder just before compression and completely vaporized. Assume that the volume of the cylinder is 485 mL and the temperature is 150C. Calculate the partial pressure of the gasoline vapor. (d) Calculate the amount (mol) of oxygen required to bum the gasoline in part (c) completely to CO2 and H2O. (e) The combustion reaction in the cylinder creates temperatures in excess of 1200K. Due to the high temperature, some of the nitrogen and oxygen in the air reacts to form nitrogen monoxide. If 10% of the nitrogen is converted to NO, calculate the mass (g) of NO produced by this combustion. (f) Hot-rod cars use another oxide of nitrogen, dinitrogen monoxide, to create an extra burst in power. When such a power boost is needed, dinitrogen monoxide gas is injected into the cylinders where it reacts with oxygen to form NO. Calculate the mass of dinitrogen monoxide that would have to be injected to form the same quantity of NO as produced in part (e). Assume that sufficient oxygen is present to do so.
perform stoichiometric ca1cu1uions for reactions involving gases as reactants or products.
Butane, C4H10, is an easily liquefied gaseous fuel. Calculate the density of butane gas at 0.857 atm and 22C. Give the answer in grams per liter
Butyl mercaptan, C4H9SH, has a very bad odor and is among the compounds added to natural gas to help detect a leak of otherwise odorless natural gas. In an experiment, you burn 95.0 mg of C4H9SH and collect the product gases (SO2, CO2, and H2O) in a 5.25-L flask at 25 C. What is the total gas pressure in the flask, and what is the partial pressure of each of the product gases?