A compressor is to be driven by a 30 hp, 2500 rpm DC motor and operating under moderate shock load with a service factor of 1.2. The compressor will operate at 600 rpm and using type B173 V-belt. The available small sheave diameter is 9 in and having a factor of 1.14. The arc of contact factor 0.89 and the length of belt factor is 0.97. Calculate the corrected center distance.

A compressor is to be driven by a 30 hp, 2500 rpm DC motor and operating under moderate shock load with a service factor of 1.2. The compressor will operate at 600 rpm and using type B173 V-belt. The available small sheave diameter is 9 in and having a factor of 1.14. The arc of contact factor 0.89 and the length of belt factor is 0.97. Calculate the corrected center distance.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A slurry pump is to be driven by a 30 HP, 2400 rpm diesel engine and operating under moderate shock load with service factor of 1.20. The pump will operate at 800 rpm and using type B V-Belt. The available small sheave diameter is 5.4 inches and having a factor of 1.14. The arc of contact is 0.89 and the length of belt factor is 0.97. Find the no. of belts used.
A 400 rpm blower is driven by a 7.5KW synchronous motor at 1750 rpm B 158 V – belt of premium quality is tobe used to transmit power. Calculate the center line of the shafts.
Two shafts made of plain carbon steel are connected by a rigid protective type flangecoupling. The shafts are running at 500 rpm. and transmit 25 kW power. Design thecoupling completely for overload capacity 25 per cent in excess of mean transmittedtorque capacity. Assume the following permissible stresses for the couplingcomponents:a. Shaft — Permissible tensile stress = 60 MPa; Permissible shear stress = 35 MPab. Keys — Rectangular formed end sunk key having permissible compressivestrength = 60 MPac. Bolts — Six numbers made of steel having permissible shear stress = 28 MPad. Flanges — Cast iron having permissible shear stress = 12 MPa
A v-belt drive is to transmit 330kW power from a pulley of 1m diameter running at 250rpm. The safe pull in each belt is 800N and the mass of the belt is 0.46kg per meter length. The angle of lap and the groove angle is 160º and 45ºrespectively. If the coefficient of friction between the belt and the pulley is 0.3. Calculate the number of belts required
The V-belt is used to deliver 7.5 kW of power at 1440 rpm from the electric motor to the fan which rotates at 480 rpm and works 24 hours a day. The transmission shaft distance is 1 m. The load correction factor (Fa) is known to be 1.3 and the type of V-belt cross-section is type B with a pitch distance correction factor (Fc) of 1.08 and an arc of contact (Fd) correction factor of 0.94. The diameter of the driving pulley is 200 mm and the driven pulley is 600 mm. Calculate: pitch distance (L)actual/corrected transmission shaft distance (C)arc of contact anglepower rating per beltnumber of belts required
A 60 hp air pump blower in 18hr/day service running at a speed of 500 rpm is driven by means of a multiple v-belt drive which is powered by a compressor-stator motor with speed 1300 rpm. The center distance must be between 30 to 40 inches and the available driver sheave diameter iS 14 inches. Recommend a multiple v-belt drive that respects the following condition stated.
3= Q + & 4qAnrm & Expert Q&A Design a shatt and tiange tor a Diesel engine in which protected type of flange coupling is to be adopted for power transmission. Th following data is availabl : for desig Power of engine = 75 kV speed of engine = 200 r.p.n maximum permissible stres?’ in shaft = 40 MPa; maximum permissible twist in shaft = 1° in length of shaft equal to 30 times the diameter of shaft; maximum torque =125 x mean torque; pitch circle diameter of bolts = 3 x diameter of shaft; maximum permissible stress in bolts = .20 MPa Il O >
Q.2 A reciprocating air compressor has a 5 ft-diameter flywheel 14 in wide, and it operates at 170 rev/min. An eight-pole squirrel-cage induction motor has nameplate data of 50 bhp at 875 rev/min. (CLO2) (a) Design a V-belt drive. (b) It is suggested that chain drive may be used for the power transmission, design a chain drive.
The machine is designed to be powered by a 100 HP electric motor at a speed of 1500 rpm, with standard D-120 V-belts. The pitch diameter of the smaller sheave is 101.6 mm and the bigger sheave is 406.4 mm. Service factor is 1.25. Use length of D-120 V-belt equal to 123.3 inches. Determine the center distance between sheaves in mm; the arc of contact in deg; and the design in HP.
A bilge pump requires 380 N.m torque at about 320 rpm. It is driven by an 1160 rpm motor by means of a roller chain. The nature of service calls for a service factor of 1.5. If the total efficiency of transmission is 95 percent, what is : The size of the motor? Number of sprocket teeth? The pitch and number of strands of the chain required?
The displacement volume of a turbocharged 4-stroke diesel engine 0.0259 m3 (25.9 Itrs) .The engine has 2200 rpm and output of 950kW. Calculate the mean effective pressure.
A gas engine working on Otto cycle has a cylinder diameter 100mm and stroke length of 125mm. The clearance volume is 300cc. Determine air standard efficiency. Assume Cp= 1.004KJ/kgK and Cv= 0.717 KJ/kgK for air.